Eko Yudiyanto

Eko Yudiyanto

Auto-generated profile, based on publicly available information

Eko Yudiyanto

State Polytechnic of Malang

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SAS Adiwidodo
S Adiwidodo
BWB Wahyudi
B Wahyudi
EYE Yudiyanto
E Yudiyanto
SSS Subagiyo
S Subagiyo
MHM Hartono
M Hartono
FBF Baananto
F Baananto
The conventional Savonius wind turbine has two inverted cylindrical blades, it can indeed receive fluid impulses from all horizontal directions and produce a greater drag force than other wind turbines. The weakness of Savonius is the resistance in one blade side. Efforts to improve that has been done is to add a blade that serves to increase the local velocity of fluid flow to resist the resistance which is termed Savonius tandem blade (STB). This research was conducted to further reduce the resistance value of one side STB with the addition of an adjustable deflector. The purpose of this study is to obtain information on changes in the torque of the STB wind turbine on variations in the deflector angle and stream velocity. The research method used is numerical simulation using CFD software. A two-dimensional view of the rotor model using deflector was considered. The deflector angle varies start from 15 degrees with an increase also every 15 degrees until the torque decreased. The CFD simulation show there is a significant increase in torque with the addition of a deflector. Maximum torque is not achieved at one deflector angle value but is also influenced by stream velocity. At higher stream velocity there is a tendency to reach the maximum torque required larger deflector angle. Then at a certain point, the torque will decrease when the deflector angle is enlarged.

26 June 2024 in Engineering Innovations
Verified
Journal Article
Open access
PDF file
RIRizki Irfin
Rizki Irfin
SASatworo Adiwidodo
Satworo Adiwidodo
EYEko Yudiyanto
Eko Yudiyanto
BWBagus Wahyudi
Bagus Wahyudi
FBFauzan Baananto
Fauzan Baananto
The Savonius and Darrieus are vertical-axis wind turbines. This turbine has resistance on one side of the blade that makes it difficult for the shaft to rotate resulting in reduced efficiency. However, the vertical shaft turbine type provides the advantage of being able to accept wind speeds from any direction without an additional tail. Savonius and Darrieus turbines show different characteristics in terms of their performances. Savonius turbine has a high power coefficient (CP) in the range of low tip speed ratio (TSR), when its TSR increases the CP will fall. In contrast to Darrieus, high CP is achieved if the TSR is also high but the CP achievement will fall at a low TSR. If it is compared to Savonius, Darrieus has higher power efficiency although it is difficult to self-start. In contrast to Savonius, Darrieus has a better self-starting ability but a lower efficiency. This study aims to improve the performance of vertical shaft wind turbines by creating a new design combination of Darrieus and Savonius turbines with deflectors to produce CP achievement on a wide TSR. The combination of the Darrieus-Savonius turbine is to improve efficiency to make self-start easier. The research method uses numerical simulation by employing CFD Ansys software. On the airfoil with a deflector angle of 70 deg, it shows that there is an increase in speed in several parts of the Darrieus blade airfoil. The increase in speed causes the decrease of static pressure in the area. The pressure difference between the sides of the airfoil surface causes a force. The direction of the force causes the turbine shaft to rotate. The deflector acts as a directional headwind, increasing the local flow velocity to counter the resistance on one side of the rotor blades The average torque produced at an angle of 70 deg is 0.5 Nm. Whereas, at an angle of 90 deg, the average torque generated is lower by around 0.15 Nm.

30 October 2025 in Eastern-European Journal of Enterprise Technologies
Verified
Journal Article
Open access
PDF file
EYEko Yudiyanto
Eko Yudiyanto
SASatworo Adiwidodo
Satworo Adiwidodo
SSSugeng Hadi Susilo
Sugeng Hadi Susilo
BPBayu Pranoto
Bayu Pranoto
The object of this study is the abrasive cutting process using thin grinding wheels, which is applied for cutting materials with various mechanical properties. The problem to be solved is mapping the energy consumption characteristics in this process through the control of cutting parameters such as grinding wheel thickness and feed rate. An experiment was conducted using grinding wheels with 1.2, 1.6, 2.0, and 3.0 mm for cutting metals. Various feed rates were used to cut Al, ST37, and cast iron, which are ductile, ductile-hard, and brittle materials. The results of the experiment show an inverse exponential relationship between the feed rate and specific energy. The 1.2 mm grinding wheel consumes up to 10% less power than the 3.0 mm wheel at low feed rates. The mapping of these characteristics enables the selection of recommended parameters. Achieving stability during the cutting process of ductile materials, the utilization of a 1.6 mm grinding wheel operating at a feed rate of 0.166 mm/s. The rigidity of the wheel determines the stability of the rotation, which depends on the thickness of the grinding wheel. The thickness of the grinding wheel determines the material removal rate of the abrasive process. Ductile-hard materials, such as ST37, require more energy because the abrasive particles must be able to break down the properties of the material to erode its surface. Ductile materials tend to cause high friction and generate heat, melting the material. The space between the abrasive particles can be filled with liquid material, causing BUE to cover the cutting edge of the abrasive particles. The application of the outcome is aimed at the machining, as a scientific basis for energy control at the manufacturing process

27 February 2025 in Technology audit and production reserves
Verified
Journal Article
Open access
PDF file
SSSugeng Hadi Susilo
Sugeng Hadi Susilo
EYEko Yudiyanto
Eko Yudiyanto
FRFatkhur Rohman
Fatkhur Rohman
WWWirawan Wirawan
Wirawan Wirawan
SASatworo Adiwidodo
Satworo Adiwidodo
MAMohammad Fadhil Bin Abas
Mohammad Fadhil Bin Abas
The object of research is the axial flux BLDC (Brushless DC) motor, widely used in electric vehicles and industrial applications due to its compact design and high efficiency. One of the most problematic areas is optimizing the stator slot configuration and coil diameter to enhance efficiency and stability. Previous studies show that these parameters significantly affect magnetic field distribution, losses, and overall performance. However, a systematic investigation is still needed. Therefore, this study aims to identify optimal parameters to improve BLDC motor efficiency and stability. In the course of the study, an experimental setup with a BLDC motor, controller, power supply, and measurement tool were used. The motor was tested with different stator slots (12 and 24) and coil diameters (0.2 mm, 0.5 mm, 0.7 mm). Measurements included power, current, speed, and temperature. Data analysis assessed the impact on efficiency and stability, supported by numerical simulations for validation and optimization. Received results show that increasing stator slots from 12 to 24 improves magnetic field distribution and motor efficiency, with power output reaching 3060 W in the optimal configuration. This is due to the proposed stator slot variation, which reduces magnetic losses and enhances thermal efficiency. In particular, motors with 24 slots and a 0.5 mm coil diameter achieved the highest efficiency, while a 0.7 mm coil led to performance decline due to increased resistance. The findings highlight the need for an optimal balance between coil diameter and stator slot configuration for stable and efficient operation. This ensures the development of high-performance BLDC motors with improved efficiency and stability. Compared to similar configurations, it offers higher power output, lower magnetic losses, and better thermal regulation. These findings support the advancement of reliable, energy-efficient BLDC motors for electric vehicles and industry, with future research focusing on advanced materials and manufacturing techniques for further optimization.

19 September 2022 in JOURNAL OF SCIENCE AND APPLIED ENGINEERING
Verified
Journal Article
Closed access
PDF file
LLListiyono Listiyono
Listiyono Listiyono
MBMuhammad Afif Bahrain
Muhammad Afif Bahrain
EYEko Yudiyanto
Eko Yudiyanto
Bioethanol is an alternative fuel to substitute fossil oil. Bioethanol has several advantages in its use as a fuel in addition to its renewable nature, and bioethanol is also believed to reduce some motor vehicle emissions. The purpose and objective of this study were to determine the effect of a mixture of Bioethanol and Pertamax on gas emissions in a 4-stroke motor with variations in the fuel mixture and engine cycle. This test method is carried out with the measurement parameters of CO, HC, CO2, and O2. Tests on motor vehicles were carried out with variations of BP0 (0% Bioethanol) to BP100 (100% Bioethanol). The test results using a gas analyzer and analyzed using excel show that bioethanol cannot reduce exhaust gas emissions. Adding bioethanol fuel to Pertamax can also increase the fuel's octane number (RON) and specific gravity. From the available data, adding bioethanol can reduce HC emission levels by up to 4ppm at BP50 at 6000 rpm, increasing CO2 emissions by 13.4% at BP50 at 7000 rpm with a compression ratio of 13:1. For the lowest O2 emission level, it reaches 0.13%. at BP40 at 5000 rpm. CO emission levels are still relatively small in various mixtures with a yield of 0.01%, but at BP0 and BP80 at 13:1 compression, emissions tend to increase every rpm.

31 October 2024 in Jurnal POLIMESIN
Verified
Journal Article
Open access
PDF file
RARadhi Nurvian Amrullah
Radhi Nurvian Amrullah
SHSyamsul Hadi
Syamsul Hadi
MRMuhammad Akhlis Rizza
Muhammad Akhlis Rizza
EYEko Yudiyanto
Eko Yudiyanto
SSSafian Sharif
Safian Sharif
Mohd Azlan SuhaimiMohd Azlan Suhaimi
Mohd Azlan Suhaimi
The impact of material selection and design on the environment in the process of making press tools for garment hanging products in sustainable manufacturing