Satworo Adiwidodo

Satworo Adiwidodo

Auto-generated profile, based on publicly available information

Satworo Adiwidodo

Politeknik Negeri Malang

Research Focus & Metrics

Academic Career Length

11Years (2016-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in IOP Conference Series: Materials Science and Engineering
Verified
Conference Paper
Open access
PDF file
SAS Adiwidodo
S Adiwidodo
BWB Wahyudi
B Wahyudi
EYE Yudiyanto
E Yudiyanto
SSS Subagiyo
S Subagiyo
MHM Hartono
M Hartono
FBF Baananto
F Baananto
The conventional Savonius wind turbine has two inverted cylindrical blades, it can indeed receive fluid impulses from all horizontal directions and produce a greater drag force than other wind turbines. The weakness of Savonius is the resistance in one blade side. Efforts to improve that has been done is to add a blade that serves to increase the local velocity of fluid flow to resist the resistance which is termed Savonius tandem blade (STB). This research was conducted to further reduce the resistance value of one side STB with the addition of an adjustable deflector. The purpose of this study is to obtain information on changes in the torque of the STB wind turbine on variations in the deflector angle and stream velocity. The research method used is numerical simulation using CFD software. A two-dimensional view of the rotor model using deflector was considered. The deflector angle varies start from 15 degrees with an increase also every 15 degrees until the torque decreased. The CFD simulation show there is a significant increase in torque with the addition of a deflector. Maximum torque is not achieved at one deflector angle value but is also influenced by stream velocity. At higher stream velocity there is a tendency to reach the maximum torque required larger deflector angle. Then at a certain point, the torque will decrease when the deflector angle is enlarged.

13 September 2021 in EUREKA: Physics and Engineering
Verified
Journal Article
Open access
PDF file
DPDony Perdana
Dony Perdana
SASatworo Adiwidodo
Satworo Adiwidodo
MCMochamad Choifin
Mochamad Choifin
WWWigo Ardi Winarko
Wigo Ardi Winarko
This study investigates the effect of attracting and repels magnetic fields with the materials of vegetable oil in the form of a mixture of coconut oil and jatropha (B50) against the behavior of stability and characteristics of flame in the process of premixed burning. The fuel for a mixture of vegetable oil of 600 ml was filled into the boiler heated with a gas stove to be evaporated at a temperature of 300 °C and 3 bar pressure was kept constant was mixed with air from the compressor in the burner room. Then a flame was ignited at the end of the nozzle to form a diffusion flame, the flame formed was then given north (N) and south (S). The results showed that the flame speed of the attractive magnetic field was 52.22 cm/sec, the repulsive magnetic field was 50.49 cm/sec while without a magnetic field was 49.79 cm/sec. The increase in the laminar flame speed in the attractive magnetic field is caused by the electron spin becoming more energetic and due to the change in the spin of the hydrogen proton from para to ortho. The attractive magnetic field has the strongest effect on increasing the flame speed. This makes the flame more stable in the equivalency ratio range of 0.75–1.17 compared to without a magnetic field in the same equivalency ratio range. This was so because O2 where it is in nature of paramagnetic was pumped more crossing the flame from south to north poles whereas the heat brought by H2O in nature of diamagnetic was pumped more crossing north to south poles. Whereas on the repel magnetic field, it was hotter when brought by H2O pumped into the flame whereas O2 tended to be pumped going out of the flame. This caused the combustion in the flame was smaller and the reaction was not maximum. As a consequence, the laminar flame speed was more lacking and the reaction was not to the fullest. As a consequence, the laminar flame speed in the repel was fewer than the attract magnetic field

26 June 2024 in Engineering Innovations
Verified
Journal Article
Open access
PDF file
RIRizki Irfin
Rizki Irfin
SASatworo Adiwidodo
Satworo Adiwidodo
EYEko Yudiyanto
Eko Yudiyanto
BWBagus Wahyudi
Bagus Wahyudi
FBFauzan Baananto
Fauzan Baananto
The Savonius and Darrieus are vertical-axis wind turbines. This turbine has resistance on one side of the blade that makes it difficult for the shaft to rotate resulting in reduced efficiency. However, the vertical shaft turbine type provides the advantage of being able to accept wind speeds from any direction without an additional tail. Savonius and Darrieus turbines show different characteristics in terms of their performances. Savonius turbine has a high power coefficient (CP) in the range of low tip speed ratio (TSR), when its TSR increases the CP will fall. In contrast to Darrieus, high CP is achieved if the TSR is also high but the CP achievement will fall at a low TSR. If it is compared to Savonius, Darrieus has higher power efficiency although it is difficult to self-start. In contrast to Savonius, Darrieus has a better self-starting ability but a lower efficiency. This study aims to improve the performance of vertical shaft wind turbines by creating a new design combination of Darrieus and Savonius turbines with deflectors to produce CP achievement on a wide TSR. The combination of the Darrieus-Savonius turbine is to improve efficiency to make self-start easier. The research method uses numerical simulation by employing CFD Ansys software. On the airfoil with a deflector angle of 70 deg, it shows that there is an increase in speed in several parts of the Darrieus blade airfoil. The increase in speed causes the decrease of static pressure in the area. The pressure difference between the sides of the airfoil surface causes a force. The direction of the force causes the turbine shaft to rotate. The deflector acts as a directional headwind, increasing the local flow velocity to counter the resistance on one side of the rotor blades The average torque produced at an angle of 70 deg is 0.5 Nm. Whereas, at an angle of 90 deg, the average torque generated is lower by around 0.15 Nm.

1 January 2023 in AIP Conference Proceedings
Verified
Conference Paper
Open access
PDF file
SASatworo Adiwidodo
Satworo Adiwidodo
FRFatkhur Rohman
Fatkhur Rohman
NANila Alia
Nila Alia
EYEko Yudiyanto
Eko Yudiyanto
State Polytechnic of Malang has a total area of 13.68 hectares. An adequate transportation mode is needed to reach the entire area. As an institution that suppo

1 January 2023 in Automotive Experiences
Verified
Journal Article
Open access
PDF file
HRHelen Riupassa
Helen Riupassa
SSSuyatno Suyatno
Suyatno Suyatno
HNHendry Y. Nanlohy
Hendry Y. Nanlohy
ASAndi Sanata
Andi Sanata
TTTrismawati Trismawati
Trismawati Trismawati
SSSelcuk Sarikoc
Selcuk Sarikoc
The burning rate of coconut oil droplets has been investigated experimentally by adding bio-additives of clove oil and eucalyptus oil. Tests were carried out with single droplets suspended on thermocouples at room atmospheric pressure, and room temperature and ignited with a hot wire. The addition of clove oil and eucalyptus oil as bio-additives into coconut oil was 100 ppm and 300 ppm, respectively. The droplet combustion method was chosen to increase the contact area between the air and fuel so that the reactivity of the fuel molecules increases. The results showed that the eugenol compounds contained in clove oil and cineol compounds in eucalyptus oil were both aromatic, and had an unsymmetrical carbon chain geometry structure. Furthermore, this factor can potentially accelerate the occurrence of effective collisions between fuel molecules. Therefore the fuel is combustible, as evidenced by the increased burning rate, where the results show that without bio-additives, the burning rate of crude coconut oil (CCO) is about 0.7 seconds. These results are 0.15 to 0.2 seconds slower than CCO with bio-additive, which is around 0.55 to 0.6 seconds. Moreover, from the observations, it was found that the highest burning rate was achieved in both bio-additives with a concentration of 300 ppm.

1 June 2016 in Applied Mechanics and Materials
Verified
Journal Article
Closed access
PDF file
SASatworo Adiwidodo
Satworo Adiwidodo
IWING Wardana
ING Wardana
LYLilis Yuliati
Lilis Yuliati
MSMega Nur Sasongko
Mega Nur Sasongko
The biggest problem of combustion in the micro-scale or meso-scale combustor is heat loss. Heat loss led to a difficult of stable flame. This research aims to elucidate the flame stabilization and flammability limit of LPG-oxygen premixed flame, temperature distribution and flame visualization. Flame stabilization and flammability limit map are shows in φ - U plane. The result shows that there are six regions in the map that is stable without noise, stable with noise, transition zone, dead zone, pseudo stable, and blow off. Measurement parameters are LPG-oxygen flow velocity at various equivalent ratio and temperature. The flame stabilization and flammability limit map within measurement parameters are discussed.