1 January 2001 in JSME International Journal Series B
15 November 2021 in Journal of Applied Physics
Information on the ionization of propellant gases is invaluable for Hall thruster plasma studies because the ion beam is the source of thrust generation. This study proposes a new method that identifies the ionization location of Xe+ ions in Hall thruster plasmas by combining the laser-induced fluorescence spectroscopy and floating emissive probe measurements in annular and cylindrical Hall thrusters. In an annular Hall thruster, this method indicated that ionization became the largest at a few millimeters upstream of the maximum radial magnetic field, whose result agreed with a one-dimensional hybrid fluid/particle-in-cell (PIC) simulation result. On the other hand, the ionization region in a cylindrical Hall thruster was located deeper inside the discharge cavity than that of the annular thruster. In addition, a large upstream shift of the ionization region was observed with the decreasing fraction of the radial magnetic field in the cylindrical Hall thruster.
1 January 2022 in Plasma Sources Science and Technology
A diagnostic system was developed for spectrally resolved, three-dimensional tomographic reconstruction of Hall thruster plasmas, and local intensity profiles of Xe I and Xe II emissions were reconstructed. In this diagnostic system, 28 virtual cameras were generated using a single, fixed charge-coupled device camera by rotating the Hall thruster to form a sufficient number of lines of sight. The Phillips–Tikhonov regularization algorithm was used to reconstruct local emission profiles from the line-integrated emission signals. The reconstruction performance was evaluated using both azimuthally symmetric and asymmetric synthetic phantom images including 5% Gaussian white noise, which resulted in a root-mean-square error of the reconstruction within an order of 10 −3 even for a 1% difference in the azimuthal intensity distribution. Using the developed system, three-dimensional local profiles of Xe II emission (541.9 nm) from radiative decay of the excited state 5p 4 ( 3 P 2 )6p 2 [3]° 5/2 and Xe I emission (881.9 nm) from 5p 5 ( 2 P° 3/2 )6p 2 [5/2] 3 were obtained, and two different shapes were found depending on the wavelength and the distance from the thruster exit plane. In particular, a stretched central jet structure was distinctively observed in the Xe II emission profile beyond 10 mm from the thruster exit, while gradual broadening was found in the Xe I emission. Approximately 10% azimuthal nonuniformities were observed in the local Xe I and Xe II intensity profiles in the near-plume region (<10 mm), which could not be quantitatively distinguished by analysis of the frontal photographic image. Three-dimensional Xe I and Xe II intensity profiles were also obtained in the plume region, and the differences in the structures of both emissions were visually confirmed.
1 December 2022 in Plasma Sources Science and Technology
Two-dimensional electron temperature and density profiles in the plume region of 300 W-class Hall thruster Ar plasmas were obtained using tomographically reconstructed optical emission intensity profiles combined with a collisional-radiative (CR) model. A total of 1242 lines of sight were used by rotating the thruster to apply inverse Radon transform-based tomographic reconstructions and Abel inversion. The reconstruction accuracy of the developed diagnostic system was evaluated using a priori images derived from plasma pictures, and the reconstruction error was less than 1% in the region of interest, exhibiting higher accuracy than the Abel inversion. From the Ar Hall thruster plasma, more than 12 different two-dimensional profiles of Ar I emission intensity within a spectral range of 600–1000 nm were obtained 6 mm from the exit plane of the thruster. A CR model using 31 allowed transitions at 15 different states from the ground state to the 2p
i
states was incorporated with the tomographically reconstructed emission intensity sets. Consequently, two-dimensional electron temperature and density profiles in the range of 5–18 eV and 2.0 × 10 16 –4.7 × 10 17 m −3 were obtained, respectively, exhibiting reasonable agreement with the double Langmuir probe measurements.
1 March 2021 in Plasma Sources Science and Technology
Two distinct discharge modes were observed in a 50 W-class micro-Hall thruster plasma under different operating conditions. A ball-shaped plasma with a broad plume (mode A) was observed at low mass flow rates (less than 0.37 mg s −1 ) over the entire operational anode voltage range (160–280 V). Raising the anode voltage beyond 200 V with the mass flow rate fixed (larger than 0.37 mg s −1 ) produced a narrow plume and stretched jet-like structure (mode B). In mode B, the thruster showed performance improvements in terms of thrust (3.8 mN vs 3.3 mN), specific impulse (913 s vs 800 s), and anode efficiency (28% vs 22%), with only a 2 W difference in the anode power (61 W in mode B and 59 W in mode A). This suggests that operation is more advantageous in mode B than in mode A for the utilization of such low-power Hall thrusters. Unique plume properties were observed in the two modes and considerable differences were measured in the Xe II ion acceleration structure, beam angle, and ionization rate as the mode changes, which were not reported in previous studies. Mode A exhibits an axially extended ion acceleration structure outside the discharge channel, where 75% of the final ion velocity is achieved at approximately 40 mm from the thruster exit, while most of the ion acceleration occurs within 10 mm from the thruster exit in mode B. Measurements show that the full width at half maximum of the Xe II ion energy distribution function, electron temperature, and Xe II emission intensity decreased after the plasma transitioned from mode A to mode B. Based on the optical emission spectroscopy, the ionization rate in the plasma plume decreased by 30%–41% after the mode change, which is likely related to the reduction of the beam angle and electron current by 24% and 30%, respectively.
27 February 2024 in Journal of Applied Physics
Laser Thomson scattering is a minimally intrusive diagnostic technique for determining electron temperature, density, and bulk velocity in plasma systems. Advances in technology have made possible the application of Thomson scattering to electric propulsion-relevant plasma systems, with reported electron number-density detection limits as low as 1×1016 m−3, and electron temperatures from one-to-tens eV. However, the implementation of laser Thomson scattering in large vacuum testing facilities, wherein electric propulsion devices are tested, remains a challenge. This work presents the implementation of a laser Thomson scattering system in a large vacuum test facility at the Georgia Tech High Power Electric Propulsion Laboratory. The diagnostic was optimized for maximum light-collection efficiency and ease of re-alignment while the facility is at vacuum. The high light-collection efficiency allowed reduced accumulation times to achieve the target detection limit of 1×1017 m−3. The diagnostic is used to measure axial electron property profiles in the near-field plume of a lanthanum hexaboride hollow cathode operating at 25 A on krypton at a background pressure of 1.3×10−6 Torr—Kr. The diagnostic is quantitatively compared to similar systems in the literature. The resulting axial points, collected from 2 to 8 mm downstream of the cathode keeper orifice, are qualitatively and quantitatively compared with simulations and experimental measurements made with electrostatic probes and laser-induced fluorescence. The main quantitative difference between measured values and results is the one to two order of magnitude difference in the peak electron density, being attributed to the relative size and location of the external anode with respect to the cathode keeper.