1 December 2022 in Plasma Sources Science and Technology
Two-dimensional electron temperature and density profiles in the plume region of 300 W-class Hall thruster Ar plasmas were obtained using tomographically reconstructed optical emission intensity profiles combined with a collisional-radiative (CR) model. A total of 1242 lines of sight were used by rotating the thruster to apply inverse Radon transform-based tomographic reconstructions and Abel inversion. The reconstruction accuracy of the developed diagnostic system was evaluated using a priori images derived from plasma pictures, and the reconstruction error was less than 1% in the region of interest, exhibiting higher accuracy than the Abel inversion. From the Ar Hall thruster plasma, more than 12 different two-dimensional profiles of Ar I emission intensity within a spectral range of 600–1000 nm were obtained 6 mm from the exit plane of the thruster. A CR model using 31 allowed transitions at 15 different states from the ground state to the 2p
i
states was incorporated with the tomographically reconstructed emission intensity sets. Consequently, two-dimensional electron temperature and density profiles in the range of 5–18 eV and 2.0 × 10 16 –4.7 × 10 17 m −3 were obtained, respectively, exhibiting reasonable agreement with the double Langmuir probe measurements.
25 December 2024 in Advanced Intelligent Systems
Accurate performance prediction methods are essential for the development of high‐efficiency Hall effect ion sources, which are employed in industries ranging from material surface treatment to spacecraft electric propulsion (known as Hall thrusters). Traditional methods rely on simplified scaling laws and computationally intensive numerical simulations. Herein, a robust machine learning model is introduced that uses a neural network ensemble to predict the performance of Hall effect ion sources based on design parameters such as discharge channel dimensions and magnetic field structure. The neural networks are trained using 18 000 data points generated from numerical simulations with input powers ranging from sub‐kW‐ to kW‐class. The accuracy of the developed machine learning model is demonstrated using untrained 700 W‐ and 1 kW‐class Hall effect ion sources, producing results with deviations of less than 10% compared to the experimentally measured thrust and discharge current, thus surpassing the accuracy of conventional scaling laws. As a high‐fidelity surrogate for numerical simulations, the proposed prediction tool provides high prediction accuracy and calculation speed, offering an excellent complement to conventional scaling laws and enhancing the understanding of Hall effect ion source performance characteristics.
1 January 2026 in Plasma Physics and Controlled Fusion
We report the experimental results of controlling the pedestal-top electron density by applying resonant magnetic perturbation (RMP) with in-vessel control coils and the main gas puff in the 2024-2025 KSTAR experimental campaign. The density is reconstructed using a parameterized grid and five channels of line-averaged density measured by the two-colored interferometer (TCI). The reconstruction procedure is accelerated by deploying a multi-layer perceptron to run in approximately 120 µ s and is sufficiently fast for real-time control. A proportional-integral controller was adopted, with the controller gains estimated from the system identification procedure. The experimental results demonstrate that the developed controller can follow a dynamic target while exclusively using both actuators. The absolute percentage errors between the electron density at and the target were approximately 1.5% median and a 2.5% average, respectively. The developed controller can even lower the density by using the pump-out mechanism under RMP, and it can follow a more dynamic range of density targets than a single actuator controller. The developed controller will enable experimental scenario exploration within a shot by dynamically setting the density target or maintaining a constant electron density within a discharge.
1 April 2024 in Physics of Plasmas
Electromagnetic fluctuations between 300 and 500 kHz were observed in both ion saturation current and magnetic field measurements in the KAERI plasma beam irradiation facility where the applied-field magnetoplasmadynamic (MPD) thruster is used as a plasma source. In this study, the plasmas were ignited with deuterium gas and the plasma current (input power) was varied from 55 A (2 kW) to 155 A (6 kW). The electron temperature and density measured downstream of the MPD thruster plasma were ∼5 eV and (2–4) × 1012 cm−3, respectively. To identify the fluctuations, the dispersion relation and the phase velocity were experimentally obtained using the Beall method and were compared to the theoretical values under warm plasma conditions. It was revealed that the observed fluctuations were fast Alfvén waves with a circularly polarized magnetic field. In addition to the fast Alfvén waves, we also observed electrostatic fluctuations at a higher frequency that was similar to the lower-hybrid frequency.
16 March 2025 in Advanced Intelligent Systems
28 May 2025 in Nuclear Fusion
Measuring the in situ erosion rate of tungsten using an optical emission spectroscopic diagnostic technique, so called the S/XB method, has recently gained attention in current fusion research. This method calculates the erosion rate by multiplying the S/XB value, which represents ionization per photon emission, with the intensity of the specific spectral line. The S/XB value was given by the ionization rates (S) and the excitation rates (X) from the ground and the metastable levels and the branching ratio (B) for the specific radiative transition of neutral tungsten (W I), assuming a corona equilibrium among the ground, metastable, and upper resonance levels. The conventional S/XB method assumes a Boltzmann distribution for metastable level densities and introduces the free parameter of the tungsten atomic characteristic temperature ( ). Herein, we propose an improved S/XB method to measure the erosion rates of tungsten in a divertor to eliminate the ambiguity caused by . Our approach directly calculates the densities of ground and metastable levels using a set of photon emission equations that relate their densities to multiple spectral line intensities within the framework of coronal equilibrium. Subsequently, the sputtered flux is obtained from the matrix operator form of S/XB and the multiple spectral line intensities given by the measurement. Our proposed method was experimentally tested using the plasma beam irradiation facility by comparing the gross tungsten erosion rates calculated using our method with those obtained from conventional approaches and those determined through the sputtering yield by the Ar+ ion beam flux. From the experiment, we obtained the sputtered tungsten flux of 4.0 × 1020 m−2 s−1 ( 2.1 × 1020) using our method at a discharge current of 150 A from the plasma source and an ion incident energy of 100 eV, while the previous method yielded a range from 1.4 × 1020 m−2 s−1–1.9 × 1021 m−2 s−1 by varying and spectral lines. Using the sputtering yield method, a sputtered flux of 4.1 × 1020 m−2 s−1 ( 1.1 × 1019) was measured as a reference value. The results demonstrate that our S/XB method significantly reduces ambiguity in the selection of spectral lines and the parameter, and closely agrees with the reference values, offering a more accurate and consistent approach for measuring tungsten erosion in fusion reactors.