We report on epitaxial growth of Bi2Se3 topological insulator thin films by Pulsed Laser Deposition (PLD). X-ray diffraction investigation confirms that Bi2Se3 with a single (001)-orientation can be obtained on several substrates in a narrow (i.e., 20 °C) range of deposition temperatures and at high deposition pressure (i.e., 0.1 mbar). However, only films grown on (001)-Al2O3 substrates show an almost-unique in-plane orientation. In-situ spin-resolved angular resolved photoemission spectroscopy experiments, performed at the NFFA-APE facility of IOM-CNR and Elettra (Trieste), show a single Dirac cone with the Dirac point at eV located in the center of the Brillouin zone and the spin polarization of the topological surface states. These results demonstrate that the topological surface state can be obtained in PLD-grown Bi2Se3 thin films.
The use of a doped Ceria buffer layer and Physical Vapour Deposition (PVD) techniques for Solid Oxide Fuel Cells (SOFC) fabrication can limit the former, the formation of electrical insulating lanthanum, and strontium zirconates at the cathode/electrolyte interface, whereas the latter allows a better control of the materials interfaces. These effects allow for operation at intermediate temperature ranges. In this work, we study the structural and electrical properties of Gadolinium Doped Ceria (GDC) barrier layer deposited via the room temperature RF Sputtering technique on anode supported electrolytes and then annealed at high temperature. The crystal structure and the surface morphology of the GDC barrier layers have been analyzed and optimized varying the temperature ramp of the post-growth annealing procedure. The electrical behavior of the obtained samples has been investigated by Electrochemical Impedance Spectroscopy and compared to that of standard SOFC with screen-printed GDC barrier layers, the former showing a maximum high frequency and low frequency resistances reduction of about 50% and 46%, respectively, with respect to the latter at an operating temperature of 650 °C. The results clearly show an important improvement of SOFC performances when using sputter deposited GDC layers, linking the electrical properties to the structural and stoichiometric ones.
1 April 2020 in International Journal of Hydrogen Energy
The superconducting properties of Sr1–xLaxCuO2 thin films are strongly affected by sample preparation procedures, including the annealing step, which are not always well controlled. We have studied the evolution of Cu L2,3 and O K edge x-ray absorption spectra (XAS) of Sr1–xLaxCuO2 thin films as a function of reducing annealing, both qualitatively and quantitatively. By using linearly polarized radiation, we are able to identify the signatures of the presence of apical oxygen in the as-grown sample and its gradual removal as a function of duration of 350 °C Ar annealing performed on the same sample. Even though the as-grown sample appears to be hole doped, we cannot identify the signature of the Zhang-Rice singlet in the O K XAS, and it is extremely unlikely that the interstitial excess oxygen can give rise to a superconducting or even a metallic ground state. XAS and x-ray linear dichroism analyses are, therefore, shown to be valuable tools to improving the control over the annealing process of electron doped superconductors.
1 February 2019 in Journal of Physics D: Applied Physics
SrCuO 2 /Sr 0.9 La 0.1 CuO 2 /SrCuO 2 trilayers were grown by oxide-molecular beam epitaxy. The thicknesses of the top and bottom SrCuO 2 layers were fixed, while the thickness of the infinite-layer electron-doped cuprate Sr 0.9 La 0.1 CuO 2 central layer was systematically changed. Transmission electron microscopy, x-ray reflectivity and x-ray diffraction measurements were performed to assess the sample quality and the abruptness of the interfaces. Electrical transport measurements as a function of temperature and as a function of central layer thickness, confirm that the normal state properties of the trilayers are altered by the confinement of the charge carriers in the central layer.