Polyimides are widely used in the MEMS and flexible electronics fields due to their combined physicochemical properties, including high thermal stability, mechanical strength, and chemical resistance values. In the past decade, rapid progress has been made in the microfabrication of polyimides. However, enabling technologies, such as laser-induced graphene on polyimide, photosensitive polyimide micropatterning, and 3D polyimide microstructure assembly, have not been reviewed from the perspective of polyimide microfabrication. The aims of this review are to systematically discuss polyimide microfabrication techniques, which cover film formation, material conversion, micropatterning, 3D microfabrication, and their applications. With an emphasis on polyimide-based flexible MEMS devices, we discuss the remaining technological challenges in polyimide fabrication and possible technological innovations in this field.
A flexible flow sensor is proposed to measure the airflow velocity and incident angle. The sensor consists of a polyimide (PI) substrate, a flat cantilever beam and a graphene piezoresistor. The cantilever beam deforms under the action of fluid-structure interaction (FSI), resulting in changes in the resistance of the graphene piezoresistor. The piezoresistor was prepared by spraying coating of graphene inks using a patterned parylene mask and then encapsulated by coating another polyimide layer to form a sandwiched structure. Experimental results indicate that the flow sensor has a wide detection range of flow velocity (0-30 m/s) and incident angle (0-25°), with a high resolution of 0.94 m/s and 0.23°, respectively. Compared with curved cantilever, the flat cantilever achieves higher sensitivity to the incident angle, and smaller disturbance to the flow field. The arrangement of the flow sensors on an airfoil is discussed for estimation of flight parameters.
14 January 2022 in IEEE Robotics and Automation Letters
Fish can perceive the surrounding flow field using their lateral line systems, consisting of canal neuromasts (CNs) for flow pressure gradient perception and superficial neuromasts (SNs) for flow velocity detection. Although various artificial lateral line (ALL) systems have been developed inspired by the lateral line of fish, few studies have combined both pressure and velocity sensors for hydrodynamic perception, and how to optimize sensor placement remains unanswered, particularly on three-dimensional models. Herein we proposed a maximized hydrodynamic stimulation strategy for sensor placement optimization. We built a fish model and designed an ALL system by mimicking the geometry of a blind cavefish, Sinocyclocheilus tianlinensis . Differential pressure sensors and hot-film flow velocity sensors were used to mimic the CNs and SNs, respectively, with optimized sensor placement. The simulation and experimental results on yaw angle detection suggested that both sensor placement of our ALL system and distribution of the biological lateral line showed good agreement with the maximized hydrodynamic stimulation strategy. Our ALL system could detect a wall within a distance of 0.1 body length, comparable to the perception ability of cave fish. The new sensor placement strategy can be used to equip ALL systems on bionic robotic fish and other underwater vehicles.
5 October 2022 in Flexible and Printed Electronics
Marine hydrological information has a significant impact on human development and the utilization of the oceans, which can be monitored with underwater sensors. In the past, ocean research has relied on the use of bulky underwater recorders and sensory telemetry networks. In this study, an integrated flexible sensor is developed for underwater conductivity, temperature, depth, and strain detection. Platinum resistance sensors were used for temperature and strain measurements, conductivity sensors with interdigitated electrodes were used for salinity measurements, and capacitive pressure sensors for depth measurements. Two kinds of flexible capacitive pressure sensors were fabricated with a carbon nanotube/polydimethylsiloxane (CNT/PDMS) bottom electrode and copper/polyimide (Cu/PI) bottom electrode. The sensor with the CNT/PDMS bottom electrode outperformed the sensor with the Cu/PI bottom electrode over a wide pressure range (<5 MPa) and showed stable capacitance up to 1000 cycles. COMSOL simulations also support our experimental results with high sensitivity of the sensor with a CNT/PDMS bottom electrode. The integrated flexible sensor is durable and lightweight, making it ideal for use as a stationary monitoring sensor or for attachment to a variety of marine animals.
The estimation of the airspeed and angle of attack (AOA) is crucial for achieving precise flight control in small unmanned aerial vehicles. A flexible skin with distributed flow sensors has been proven to be an effective approach to estimate flight parameters, particularly, pressure-airflow data fusion strategies can improve estimation accuracy. For the first time, we fabricate propose an ultra-thin (70 μm) all-polyimide flexible skin integrated with capacitive pressure sensors and piezoresistive airflow sensors. The ultra-thin structure of the flexible skin endows it with flexibility and adaptability to curved airfoils and avoids disturbing the flow field near the surface. Meanwhile, the rational arrangement of the sensors on the leading edge of the airfoil makes them insensitive to the angle of sideslip (AOS). The pressure and airflow sensors achieve a resolution of 4.5 Pa and 2.4 m/s, respectively. Using a simple multi-layer perceptron (MLP) neural network, we estimate the average solving errors of airspeed and AOA to be 0.79 m/s and 0.67°, respectively. Compared with traditional methods, the proposed flexible skin considerably reduces the workload by decoupling the airspeed, AOA and AOS, providing a facile method for efficient and accurate flight parameter estimation.
This paper presents a novel silicon piezoresistor on polyimide (SPOP) technique for fabrication of differential pressure sensors (DPS). Inspired by the bristled wing configuration of tiny wasps, a bristled polyimide (PI) cantilever was designed to detect the differential pressure caused by the aerodynamic loading on the surface of the cantilever. Compared with the conventional silicon-based DPS, the proposed DPS has a wide detection range, due to the large deformation of the flexible bristled cantilever and the enhanced leakage between the bristles. Boron doped silicon was employed as the sensing material to improve the sensitivity of DPS. Experimental results indicate that the DPS has a high repeatability in the detection range of ±1000 Pa, and exhibits sensitivity compression in high pressure ranges. In addition, the sensitivity and resolution of the DPS are as high as 7.27×10 -5 Pa -1 and 0.32 Pa, respectively. Compared to other DPS, the cantilever based SPOP-DPS exhibits a higher sensitivity in a wide detection range, resulting in promising applications.