27 October 2020 in Optics Letters
Laser damage in fused silica, particularly ultraviolet laser damage, is still a key problem limiting the development of high-power laser systems. In this Letter, a combined process of chemical etching and laser polishing was applied to ground fused silica. A super-smooth surface with a root-mean-square roughness of 0.25 nm was achieved through this combined process. Furthermore, the combined process can reduce the introduction of photoactive metal impurity elements, destructive defects, and chemical-structure defects, resulting in a 0% probability damage threshold nearly 33% higher than a conventional chemical mechanical polished sample for a 7.6 ns pulse at a wavelength of 355 nm.
1 January 2022 in High Power Laser Science and Engineering
High-power continuous-wave single-frequency Er-doped fiber amplifiers at 1560 nm by in-band and core pumping of a 1480 nm Raman fiber laser are investigated in detail. Both co- and counter-pumping configurations are studied experimentally. Up to 59.1 W output and 90% efficiency were obtained in the fundamental mode and linear polarization in the co-pumped case, while less power and efficiency were achieved in the counter-pumped setup for additional loss. The amplifier performs indistinguishably in terms of laser linewidth and relative intensity noise in the frequency range up to 10 MHz for both configurations. However, the spectral pedestal is raised in co-pumping, caused by cross-phase modulation between the pump and signal laser, which is observed and analyzed for the first time. Nevertheless, the spectral pedestal is 34.9 dB below the peak, which has a negligible effect for most applications.
22 March 2023 in High Power Laser Science and Engineering
The phase summation effect in sum-frequency mixing process is utilized to avoid a nonlinearity obstacle in the power scaling of single-frequency visible or ultraviolet lasers. Two single-frequency fundamental lasers are spectrally broadened by phase modulation to suppress stimulated Brillouin scattering in fiber amplifier and achieve higher power. After sum-frequency mixing in a nonlinear optical crystal, the upconverted laser returns to single frequency due to phase summation, when the phase modulations on two fundamental lasers have a similar amplitude but opposite sign. The method was experimentally proved in a Raman fiber amplifier-based laser system, which generated a power-scalable sideband-free single-frequency 590 nm laser. The proposal manifests the importance of phase operation in wave-mixing processes for precision laser technology.
3 March 2022 in Optics Express
A robust 20-W continuous-wave single frequency 589 nm laser is developed to aim for sodium guide star in astronomy. The source is based on applying π-depth binary phase modulation to a single frequency seed laser along with 3 steps of strain in the gain fiber to suppress the stimulated Brillouin scattering in the high power 1178 nm amplifier and realizing the recovery of single frequency after frequency doubling in a periodically poled LiTaO3 crystal. The efficiency of frequency doubling reaches up to 41.6%. To the best of our knowledge, it is the highest power reported for continuous-wave 589 nm laser generation by single-pass frequency doubling. The approach significantly simplifies the sodium guide star laser design and improves robustness.
3 January 2022 in Optics Letters
In second harmonic generation, the phase of the optical field is doubled, which has important implications. Here, the phase-doubling effect is utilized to solve a long-standing challenge in the power scaling of single-frequency laser. (−π/2, π/2) binary phase modulation is applied to a single-frequency seed laser to broaden the spectrum and suppress the stimulated Brillouin scattering in a high-power fiber amplifier. The second harmonic of the phase-modulated laser returns to single frequency because the (−π/2, π/2) modulation is doubled to (−π, π) for the second harmonic. A compression-to-single-frequency rate as high as 95% is demonstrated in experiments limited by the electronic bandwidth of the setup. Such phase manipulation in wave-mixing processes may open up a new field of development in nonlinear optics and laser technology.
7 May 2021 in Optics Express
Spectral and relative intensity noise (RIN) characteristics of a single-frequency Raman fiber amplifier co-pumped by amplified spontaneous emission (ASE) sources are investigated experimentally. Due to the relatively lower intensity noise of ASE sources compared to usual fiber laser pumps, the full width at half maximum (FWHM) linewidth of the signal laser increases negligibly. But there is significant increase in RIN and spectral wings due to the noise transfer at high frequency from the ASE source during the Raman amplification. The deterioration can be suppressed to some extent with ASE of broader linewidth, which has lower intensity noise.