Sigmund Kyrre Ås

Sigmund Kyrre Ås

Auto-generated profile, based on publicly available information

Sigmund Kyrre Ås

SINTEF Materials and Chemistry, Trondheim, Norway

Research Focus & Metrics

Academic Career Length

15Years (2012-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 March 2012 in Computational Materials Science
Verified
Journal Article
Closed access
AAAmin S. Azar
Amin S. Azar
SÅSigmund K. Ås
Sigmund K. Ås
OAOdd M. Akselsen
Odd M. Akselsen

1 June 2018 in International Journal of Fatigue
Verified
Journal Article
Closed access
Håkan HallbergHåkan Hallberg
Håkan Hallberg
SÅSigmund Kyrre Ås
Sigmund Kyrre Ås
BSBjørn Skallerud
Bjørn Skallerud

1 December 2018 in International Journal of Fatigue
Verified
Journal Article
Open access
BSBjørn Skallerud
Bjørn Skallerud
SÅSigmund Kyrre Ås
Sigmund Kyrre Ås
NONiels S. Ottosen
Niels S. Ottosen

Verified
Journal Article
Open access
PDF file
LSLuca Savio
Luca Savio
LSLucia Sileo
Lucia Sileo
SÅSigmund Kyrre Ås
Sigmund Kyrre Ås
Results of the fluid-structure co-simulations that were carried out as part of the FleksProp project are presented. The FleksProp project aims to establish better design procedures that take into account the hydroelastic behavior of marine propellers and thrusters. Part of the project is devoted to establishing good validation cases for fluid-structure interaction (FSI) simulations. More specifically, this paper describes the comparison of the numerical computations carried out on three propeller designs that were produced in both a metal and resin variant. The metal version could practically be considered rigid in model scale, while the resin variant would show measurable deformations. Both variants were then tested in open water condition at SINTEF Ocean’s towing tank. The tests were carried out at different propeller rotational speeds, advance coefficients, and pitch settings. The computations were carried out using the commercial software STAR-CCM+ and Abaqus. This paper describes briefly the experimental setup and focuses on the numerical setup and the discussion of the results. The simulations agreed well with the experiments; hence, the computational approach has been validated.

3 August 2012 in Journal of Materials Engineering and Performance
Verified
Journal Article
Closed access
PDF file
AAAmin S. Azar
Amin S. Azar
SÅSigmund K. Ås
Sigmund K. Ås
OAOdd M. Akselsen
Odd M. Akselsen

11 September 2022 in Fatigue & Fracture of Engineering Materials & Structures
Verified
Journal Article
Open access
PQPaul Qvale
Paul Qvale
EZErshad P. Zarandi
Ershad P. Zarandi
AAAlberto Arredondo
Alberto Arredondo
SÅSigmund K. Ås
Sigmund K. Ås
BSBjørn H. Skallerud
Bjørn H. Skallerud
Corroded surfaces of offshore mooring chains typically show a very irregular shape with different pit geometries. Fatigue tests were performed in three‐point bending on specimens with hemispherical notches, representing an idealized geometry of a corrosion pit. Digital image correlation was used to detect crack initiation lives and locations. The aim of the study was to quantify mean stress relaxation (MSR) and its influence on fatigue initiation life. MSR data were obtained from strain‐controlled fatigue tests on R4‐grade offshore mooring chain steel. Interestingly, MSR was observed even at a stress amplitude below the cyclic yield stress. For initiation lives below 100,000 cycles, significant improvement in predictions was obtained if cyclic softening and MSR were accounted for. Using only the monotonic stress‐strain curve led to less accurate predictions. For longer lives, scatter in the base material data and residual stresses from machining of the notch made predictions less accurate.