An impulse radio ultra-wideband (IR-UWB) transceiver with digitalized multipulse position modulation (D-MPPM) is proposed for high-data-rate, low-power, and short-range communication. The D-MPPM overcomes the data-rate dependence on the system clock frequency by modulating data with the time difference between the two pulses and also allows fully digital circuit-based modulation and demodulation. With this technique, the data rate is improved by a factor of 5 compared to conventional IR-UWB modulation schemes at the same clock frequency, which results in 4.28-dB link margin enhancement compared to bi-pulse position modulation (BPPM). Also, the technique makes it possible to design a clockless receiver, which allows more compact and power efficient design. Thus, it can achieve 500 Mb/s with 27.7-mW power consumption for Rx and 7 mW for Tx and the radio range of 1-5 m.
5 November 2019 in IEEE Transactions on Microwave Theory and Techniques
In this article, a wideband differential low-noise amplifier (LNA) for multiband wireless communication applications is proposed. First, shunt peaking is implemented with a self-biased active inductor (AI) to realize wideband characteristics in a compact size. Second, a cross-coupled capacitor is added to the AI, thus constructing a feedforward path. It adds a signal to the output node so that the bandwidth (BW) can be further increased by compensating the gain reduction according to the frequency. Additionally, the feedforward path creates another feedback loop, generating a negative capacitance. The negative capacitance can cancel parasitic capacitance to increase BW with a cascade amplifier. The prototype LNA is fabricated with a 65-nm CMOS process. It has a gain of 26.7 dB and a BW of 4.1 GHz. The noise figure (NF) is 3 dB and the third-order input intercept point (IIP3) is -14.2 dBm at 2 GHz. It consumes 13.9 mA at a 1-V supply and has an area of 0.009 mm 2 .
30 January 2020 in IEEE Journal of Solid-State Circuits
This article introduces a time-domain-based artificial intelligence (AI) radar system for gesture recognition using 33-GS/s direct sampling technique. High-speed sampling using a time-extension method allows AI learning to be applied to a time-domain radar signal reflecting information on both dynamic and static gestures, and thus can recognize not only dynamic but also static gestures. The Vernier clock generators and high-speed active samplers applied with the time-extension technique makes sampling at 33 GS/s possible. A 1-D convolutional neural network and long short-term memory are employed for both static and dynamic gestures and recognition rates of 93.2% and 90.5% are obtained, respectively. The radar system is implemented using a 65-nm CMOS process with a power consumption of 95 mW.
20 June 2022 in IEEE Journal of Solid-State Circuits
An impulse radio ultra-wideband (IR-UWB) transceiver is implemented with low power, high data rate communication techniques, such as extended multipulse position modulation (E-MPPM), cross-coupled (CC) envelope detection, and digital frequency hopping (DFH). The use of the E-MPPM helps increase the modulation efficiency. The capacitive-CC technique helps improve the sensitivity by increasing the conversion gain of an envelope detector. DFH increases the pulse energy of a transmitted impulse without sacrificing the power spectral density (PSD) requirement. The proposed CMOS transceiver achieves a data rate of 1.125 Gbps and a radio range of 2 m with a power consumption of 28 mW and energy efficiency of 24.9 pJ/b.
24 May 2017 in IEEE Journal of Solid-State Circuits
This paper presents an impulse-radio ultra-wideband (IR-UWB) receiver design for precise wireless ranging using a newly proposed direct sampling with time-extension (DTE) method. To overcome the problems encountered in high-speed sampling for impulse signals, the DTE method, which exploits the characteristics of an impulse, is proposed. The proposed method performs high-speed sampling only during the period when short pulses exist, and quantizes the sampled signal during the dead time where no pulses exist. The high-speed impulse signal can be easily digitized using low-speed analog-to-digital converter. We designed and fabricated the IR-UWB receiver using a 65-nm CMOS process. The measurement result shows a 1.9-mm resolution for indoor wireless ranging within a 1-m range. The receiver has a power consumption of 70 mW at 1.2 V and energy efficiency of 1554 nJ/pulse.
1 August 2012 in IEEE Transactions on Circuits and Systems II: Express Briefs
This brief implements an impulse radio ultrawideband receiver (Rx) for accurate wireless ranging. The ranging accuracy of ±9.7 mm is achieved in a multipath environment by employing the proposed leading edge detection method with a time-to-digital converter (TDC). The Rx extracts the leading edge of the input pulse, and the TDC measures the time of arrival, which is the time interval between the leading edge of a received signal and the reference clock synchronized with a transmitter (Tx). The Rx is implemented with 130-nm CMOS and consumes 46.8 mW.