2 February 2024 in Science
High-purity precursor materials are vital for high-efficiency perovskite solar cells (PSCs) to reduce defect density caused by impurities in perovskite. In this study, we present aqueous synthesized perovskite microcrystals as precursor materials for PSCs. Our approach enables kilogram-scale mass production and synthesizes formamidinium lead iodide (FAPbI 3 ) microcrystals with up to 99.996% purity, with an average value of 99.994 ± 0.0015%, from inexpensive, low-purity raw materials. The reduction in calcium ions, which made up the largest impurity in the aqueous solution, led to the greatest reduction in carrier trap states, and its deliberate introduction was shown to decrease device performance. With these purified precursors, we achieved a power conversion efficiency (PCE) of 25.6% (25.3% certified) in inverted PSCs and retained 94% of the initial PCE after 1000 hours of continuous simulated solar illumination at 50°C.
18 April 2019 in Physical Review Letters
Because of their weak interlayer bonding, van der Waals (vdW) solids are very sensitive to external stimuli such as strain. Experimental studies of strain tuning of thermal properties in vdW solids have not yet been reported. Under cross-plane compressive strain created by hydrostatic pressure in a diamond anvil cell, we observed an increase of cross-plane thermal conductivity in bulk from 3.5 to about , measured with a picosecond transient thermoreflectance technique. First-principles calculations and coherent phonon spectroscopy experiments reveal that this drastic change arises from the strain-enhanced interlayer interaction, heavily modified phonon dispersions, and decrease in phonon lifetimes due to the unbundling effect along the cross-plane direction. The contribution from the change of electronic thermal conductivity is negligible. Our results suggest possible parallel tuning of structural, thermal, and electrical properties of vdW solids with strain in multiphysics devices.
22 June 2017 in npj 2D Materials and Applications
In two dimensional (2D) transition metal dichalcogenides, defect-related processes can significantly affect carrier dynamics and transport properties. Using femtosecond degenerate pump-probe spectroscopy, exciton capture, and release by mid-gap defects have been observed in chemical vapor deposition (CVD) grown monolayer MoSe2. The observed defect state filling shows a clear saturation at high exciton densities, from which the defect density is estimated to be around 0.5 × 1012/cm2. The exciton capture time extracted from experimental data is around ~ 1 ps, while the average fast and slow release times are 52 and 700 ps, respectively. The process of defect trapping excitons is found to exist uniquely in CVD grown samples, regardless of substrate and sample thickness. X-ray photoelectron spectroscopy measurements on CVD and exfoliated samples suggest that the oxygen-associated impurities could be responsible for the exciton trapping. Our results bring new insights to understand the role of defects in capturing and releasing excitons in 2D materials, and demonstrate an approach to estimate the defect density nondestructively, both of which will facilitate the design and application of optoelectronics devices based on CVD grown 2D transition metal dichalcogenides.
29 August 2017 in Scientific Reports
All-optical switches have been considered as a promising solution to overcome the fundamental speed limit of the current electronic switches. However, the lack of a suitable third-order nonlinear material greatly hinders the development of this technology. Here we report the observation of ultrahigh third-order nonlinearity about 0.45 cm2/GW in graphene oxide thin films at the telecommunication wavelength region, which is four orders of magnitude higher than that of single crystalline silicon. Besides, graphene oxide is water soluble and thus easy to process due to the existence of oxygen containing groups. These unique properties can potentially significantly advance the performance of all-optical switches.
19 December 2017 in ACS Applied Materials & Interfaces
1 May 2018 in APL Materials
Defect-carrier interaction in transition metal dichalcogenides (TMDs) plays important roles in carrier relaxation dynamics and carrier transport, which determines the performance of electronic devices. With femtosecond laser time-resolved spectroscopy, we investigated the effect of grain boundary/edge defects on the ultrafast dynamics of photoexcited carrier in molecular beam epitaxy (MBE)-grown MoTe2 and MoSe2. We found that, comparing with exfoliated samples, the carrier recombination rate in MBE-grown samples accelerates by about 50 times. We attribute this striking difference to the existence of abundant grain boundary/edge defects in MBE-grown samples, which can serve as effective recombination centers for the photoexcited carriers. We also observed coherent acoustic phonons in both exfoliated and MBE-grown MoTe2, indicating strong electron-phonon coupling in this materials. Our measured sound velocity agrees well with the previously reported result of theoretical calculation. Our findings provide a useful reference for the fundamental parameters: carrier lifetime and sound velocity and reveal the undiscovered carrier recombination effect of grain boundary/edge defects, both of which will facilitate the defect engineering in TMD materials for high speed opto-electronics.