In this work, the influence of maleic anhydride grafted polypropylene (PP-g-MA) content on thermal and me-chanical properties of polypropylene (PP) composites with two types of clays, differing modifier density in the interlayer space, Cloisite15A and Cloisite20A, was studied. PP/clay composites were melt blended in presence of different content of PP-g-MA from 3, 6, 9, and 12 wt.%. It was found that Cloisite15A with a high density of the modifier promotes the formation of intercalated structures, while Cloisite20A with a low density of the modifier, predominantly exfoliated nanocomposites are formed. In the first case, the structure tends to become intercalated whilst composites with Cloisite20A favor the formation of predominantly exfo-liated structures. The formation of the nanocomposite is accompanied by a significant increase in thermal sta-bility (50 % weight loss is observed at temperatures of 360 °C and 430 °C for polypropylene and nanocomposites based on it, respectively). An analysis of the mechanical properties of nanocomposites gen-erally indicates an increase in the elastic modulus by 15–20 %, and this effect is more pronounced for exfoli-ated structures, the yield strength practically does not change and the elongation at break decreases noticeably.
A multiscale computational investigation integrating density functional theory (DFT) and molecular dynamics (MD) simulations was conducted to elucidate the mechanisms through which sulfur-containing donor molecules stabilize the photoactive α-phase of formamidinium lead iodide (FAPbI3) perovskites. The binding energetics, charge-transfer behavior, and hydrogen-bonding interactions of thiourea (TU), thiosemicarbazide (TSC), thiocyanate (SCN–), and diethyldithiocarbamate (DTC) were systematically analyzed. DFT results revealed pronounced Pb–S coordination and multidentate hydrogenbonding, with binding energies following the trend SCN–>TSC>DTC>TU. Thermodynamic analysis demonstrated that these additives lower the Gibbs free energy difference, thereby stabilizing the black α-phase, with TSC, TU, and to a lesser extent DTC exhibitingthe most pronounced effects. Projected density of statesanalysis confirmed that TU and DTC effectively suppressed trap states near the band edges without introducing midgap defects. MD simulations demonstrated preferential adsorption of all S-donors on FAPbI3 (001) surfaces, forming three to four hydrogen bonds per frame and achieving adsorption energies up to −52 kJ∙mol-1. These findings reveal a direct correlation between coordination strength, electronic coupling, and thermodynamic stabilization, establishing TU, TSC, and DTC as promising additives for improving the phase stability and electronic performance of FAPbI3-based perovskite solar cells.
14 April 2023 in Journal of science and innovative development
In this work, polymer composite materials based on polypropylene (PP) and layered silicates were obtained by melt mixing method. The research looked into the effect of the amount of compatibilizer on thermal and mechanical properties of composites based on two types of layered silicates with modifiers of different interlayer densities, with maleic anhydride grafted polypropylene (MA-p-PP), which was used as a compatibilizer. The compatibilizer was changed to 3, 6, 9 and 12 % while the amount of filler in the composite remained at 3 %. Cloisite15A, a layered silicate with a higher modifier density, produced intercalated structures, while Cloisite20A, with a relatively lower modifier density, produced mostly exfoliated nanocomposites. Forming of the nanostructure led to a significant increase in thermal stability (50 % weight loss was observed at temperatures of 360 and 430 °C for polypropylene and its based nano-composites, respectively). The analysis of the mechanical properties of nanocomposites showed that the elastic modulus increases by 15–20 %, and this effect is more expressive for exfoliated structures, however, the yield stress remains practically unchanged, and a significant decrease in elastic deformation is observed.