21 February 2018 in IEEE Transactions on Industry Applications
This paper presents a reliable micro-grid for residential community with modified control techniques to achieve enhanced operation during grid connected, islanded and re-synchronization mode. The proposed micro-grid is a combination of solar photo-voltaic (PV), battery storage system and locally distributed DG systems with residential local loads. A modified power control technique is developed such that, local load reactive power demand, harmonic currents and load unbalance is compensated by respective residential local DG. However, active power demand of all local residential load is shared between the micro-grid and respective local DG. This control technique also achieves constant active power loading on the micro-grid by supporting additional active power local load demand of respective residential DG. Hence, proposed modified power control technique achieves transient free operation of the micro-grid during residential load disturbances. An additional modified control technique is also developed to achieve seamless transition of micro-grid between grid connected mode and islanded mode. The dynamic performance of this micro-grid during grid connected, islanded and re-synchronization mode under linear and non-linear load variations is verified using real time simulator (RTS).
22 June 2015 in IEEE Transactions on Industrial Electronics
MBMakarand Sudhakar Ballal
This paper presents high step-up dc-to-dc converter for low voltage sources such as solar photovoltaics, fuel cells, and battery banks. To achieve high voltage gain without large duty cycle operation, combination of coupled inductor and switched capacitor voltage doubler cells are used. By incorporating active clamp circuit, voltage spike due to the leakage inductance of the coupled inductor is alleviated and zero-voltage switching turn on of the main and auxiliary switch is obtained. Due to the use of MOSFETs of low voltage rating and soft turn on of the switches, conduction loss and switching losses are reduced. This improves the efficiency and power density of the converter. The proposed converter can achieve high voltage gain with reduced voltage stress on MOSFET switches and output diodes. Design and analysis of the proposed converter is carried out, and finally, a 500-W experimental prototype is built to verify theoretical analysis.
14 September 2017 in IEEE Transactions on Industry Applications
A two-stage grid tied efficient solar photovoltaic (SPV) system with zero voltage switching (ZVS) and zero current switching (ZCS) at DC-DC converter stage and adaptive synchronization at inverter stage is proposed. In the first stage, an improved high step-up boost integrated flyback converter with quasi resonant voltage multiplier cell is proposed. ZVS turn-on of all MOSFETs and ZCS turn-off of all diodes of resonant voltage multiplier cell results in high efficient power conversion compared to the conventional boost integrated flyback converters. Small sized coupled inductor enhances magnetic utilization in this converter. Second stage consists of a single phase H-bridge grid interfaced inverter with variable band hysteresis current control technique. Amplitude adaptive notch filter (AANF) is used to extract fundamental unit voltage vector of grid voltage required for estimation of synchronized reference current for hysteresis controller. A 250W laboratory prototype is developed and experimentally evaluated. Experimental results demonstrate efficient renewable energy conversion at DC-DC converter stage and quality power injection at DC-AC inverter stage of the proposed grid tied SPV system under changing solar insulation levels.
2 November 2017 in IEEE Transactions on Power Electronics
An isolated four channel dc/dc converter with zero voltage switching is proposed as the front-end of multiple inverter structures to integrate renewable and other low voltage energy sources to micro grids. The interleaving technique is adopted to connect each module of proposed converter to a common dc source. This dc source can be a fuel cell stack, PV panels, battery, or any other low voltage dc source. All four channels are interleaved and a phase shift of 90° is provided between the gate signals of each channels, which reduces the input current ripple. The output port of the proposed converter provide four isolated and regulated dc voltages. These isolated dc sources can be connected in series or parallel or series-parallel manner to obtain required dc-link voltage of various inverter structure. Issues like capacitor voltage balancing of diode clamped multilevel inverters can overcome through the proposed converter. By incorporating a coupled inductor for isolation and energy storage along with voltage multiplier circuit, the proposed converter can achieve higher voltage step up with lower turns ratio and lower voltage stress at moderate duty ratio. Hence, mosfets of low voltage rating (low R DS (ON)) can be utilized to reduce conduction loss. A 2 kW prototype of the proposed interleaved dc/dc converter is developed and tested with diode clamped three-level inverter, five-level inverter, and three-phase two-level inverter to verify the design.
7 February 2017 in IEEE Transactions on Industrial Informatics
This paper presents real-time implementation of a grid interfaced distributed generation (DG) system with modified current control loop using three phase amplitude adaptive notch filter (AANF) based synchronization tool. A grid current feedback based modified dq-current control technique for interfacing inverter is developed in order to achieve constant loading on the grid, transient-free operation, and power factor improvement close to unity power factor (UPF) of the utility grid during sudden load variations. This technique does not require separate calculation of reference reactive component and harmonics component of currents hence reduces control circuit complexity. In addition, it requires only three voltage and three current sensors. Three phase AANF is developed and is used for online extraction of utility voltage phase angle to generate synchronized reference current signals for interfacing inverter. AANF is used because of its adjustable accuracy and amplitude adaptability even under unbalanced voltage sag and swell, frequency variation, and distorted grid conditions. Fast and accurate behavior of three phase AANF improves the dynamic response of entire DG system control performance for sudden load variations. The dynamic behavior of the proposed grid interfaced DG system is experimentally evaluated in maintaining constant loading on grid, transient-free operation, and power factor improvement close to UPF operation of the utility grid, by compensating total reactive power and harmonic current demanded by variable linear as well as nonlinear load.