This research discusses the results of experiments performed on a large-scale gasification installation to determine the influence of total system pressure and partial pressure of CO2 on the efficiency of conversion and the quality of the produced gas. The three tested feedstocks were bark, lignin and a blend of bark and wheat straw, while softwood pellet (SWP) was used as a reference fuel. A mixture of O2/CO2/H2O was used as a gasification agent. The tests were devised to validate the previously proposed process parameters, verify whether similar ash agglomeration problems would occur and compare the thermal behaviour of the feedstocks converted in close-to-industrial process conditions. An understanding of the effect of using CO2 for gasification was further deepened, especially regarding its influence on the yield of H2 and temperature profiles of the fluidized bed. The influence of gasification pressure was predominantly visible in higher yields of all hydrocarbons (including CH4) and lower overall production of producer gas. At the process development unit (PDU), all tested feedstocks were converted at similar process conditions and no signs of potential bed agglomeration could be noticed. This opposes the findings observed in smaller-scale bubbling fluidized bed (BFB) tests. The discussion behind these discrepancies is also presented.
In this research, the idea of multicomponent, one-vessel cleaning of syngas through simultaneous dedusting and adsorption is described. Data presented were obtained with the use of a pilot-scale 60 kWth fixed-bed GazEla reactor, coupled with a dry gas cleaning unit where mineral sorbents are injected into raw syngas at 500–650 °C, before dedusting at ceramic filters. The research primarily presents results of the application of four calcined sorbents, i.e., chalk (CaO), dolomite (MgO–CaO), halloysite (AlO–MgO–FeO), and kaolinite (AlO–MgO) for high-temperature (HT) adsorption of impurities contained in syngas from gasification of biomass. An emphasis on data regarding the stability of the filtration process is provided since the addition of coating and co-filtering materials is often necessary for keeping the filtration of syngas stable, in industrial applications.
The subject of the article is the assessment of the environmental impact of the technology concerning the use of low-quality post-process gas for the production of electricity and heat, along with the treatment of post-process wastewater. This assessment was carried out based on the results of the full life cycle assessment (LCA) analysis. The presented technology is based on the energetic use of low-quality process gases in a reciprocating engine for the production of electricity and heat in cogeneration with the use of heat in the wastewater treatment system. The article presents the adopted assumptions and the results of the LCA analysis for the RECLEG technology developed specifically for a zinc smelter. The aim of the analysis was to check whether the developed technology has a positive impact on the environment. The LCA analysis was performed using the ReCiPe methodology, which is one of the most frequently used methodologies in this field due to the possibility of observing the environmental impact in a full range of different environmental aspects. At the same time, the analysis also allows the results to be presented in three general impact categories: human health, ecosystem and natural resources, which are easier to interpret. By converting the waste post-process gas into electricity and heat, it is seen that this has a positive impact on the environment. Especially due to the waste nature of the source, which is the post-process gas. Each reduction of gas is potentially beneficial for the environment and, in addition, a replacement effect can be observed, because the gas was previously burned in a flare, where it additionally emitted exhaust gases, sent directly to the atmosphere. Moreover, the RECLEG technology combines post-process wastewater treatment, which has a positive effect on water management, and makes the process even more environmentally friendly.
1 May 2019 in IOP Conference Series: Materials Science and Engineering
The article presents a topic related to generation of heat and power in small and medium size coal power units which are able to comply with the emission benchmark of 550 g of CO2/kWh through utilization of biomass. The concept for coal and biomass cogasification installation is based on GazEla reactor, which has been developed by Institute for Chemical Processing of Coal. Authors also present a discussion on issues related to technological scheme of the gasification unit which has been integrated with a selected district heating system. The system has been set up for generation of hot technological water and electrical power. Focal point of the installation is a fixed bed gasification reactor. For the system to provide means enabling cogeneration of heat and power, downstream from the generator a high-temperature gas dedusting system, a unit for recovery of heat from process gas coupled with separation of tar contaminants as well as a gas engine were proposed. A sorted chart presenting historical data for annual demand for heat together with the most important assumptions used during the analyses are discussed. Finally authors present results of calculations for the integrated unit that are further broadened by sensitivity analyses for change of gasification reactor’s efficiency, as well as engine’s efficiency for heat and power generation.