William Villamil

William Villamil

Auto-generated profile, based on publicly available information

William Villamil

University of Illinois Urbana-Champaign

Research Focus & Metrics

Academic Career Length

2Years (2025-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 May 2025
Verified
Report
Closed access
AUArizona State University
Arizona State University
AJAngeli Jayme
Angeli Jayme
JHJaime Hernandez
Jaime Hernandez
MUMarquette University
Marquette University
Imad Al-QadiImad Al-Qadi
Imad Al-Qadi
WVWilliam Villamil
William Villamil
Heavy-duty electric vehicles (HDEV) pose challenges to flexible pavements. This study evaluated four Illinois pavement structures to quantify HDEV impacts on pavements. Compounding factors included increases in load and acceleration, which escalated critical strains and reduced repetitions to failure. Various distresses were considered: bottom-up cracking, shear-driven top-down cracking, and shear-driven shoving. A proposed framework is presented, which includes a new metric—e-truck adjustment factor—that enables a full truck comparison of internal combustion engine vehicles (ICs) with HDEVs. The driving factor for HDEV’s effect was the additional shear strain in the pavement structure. For pavements with relatively thin hot-mix asphalt (HMA) layers (e.g., low volume and typical thick), the increased load impact was prominent. In addition, the impact adversely affected the subgrade and base layer with higher induced structural rutting. Pavement sections with either a relatively thick HMA layer (e.g., full depth) or supported by a high-modulus layer (e.g., stone matrix asphalt [SMA] overlay on Portland cement concrete) were impacted by the increasing acceleration. In that case, the horizontal shear strain near the surface aligned with the increased longitudinal contact stresses. Hence, determining HDEVs’ impact on pavement should consider battery placement and acceleration increase as well as pavement’s structural configuration, which define governing distresses. Full-depth and SMA-overlay sections displayed an increase in near-surface shearing, which may increase maintenance and rehabilitation frequency or warrant the use of shear-resistant materials. The environmental and economic impacts of the scenarios considered were assessed. HDEVs may reduce use-stage costs due to vehicle design efficiency but may escalate pavement maintenance expenses. In addition, the impact of reduced truckload capacity of HDEVs compared to ICs may warrant additional trips to transport the same amount of freight.

2 February 2026 in International Journal of Pavement Engineering
Verified
Journal Article
Closed access
HLHong Lang
Hong Lang
WVWilliam D. Villamil
William D. Villamil
Imad Al-QadiImad Al-Qadi
Imad Al-Qadi

1 September 2026
Verified
Report
Closed access
Imad Al-QadiImad Al-Qadi
Imad Al-Qadi
MGMani Golparvar-Fard
Mani Golparvar-Fard
MFMohammad Fakhreddine
Mohammad Fakhreddine
HLHong Lang
Hong Lang
WVWilliam Villamil
William Villamil
This study developed a contactless and automated technique to estimate hot-mix asphalt pavement surface friction by combining computer vision image–based 3D reconstruction with machine learning. Existing continuous friction estimation equipment, including high-speed laser scanners, are costly to purchase and operate—limiting routine, frequent monitoring. This study addressed this limitation through the development and utilization of cost-effective and scalable equipment. A Structure-from-Motion computer vision framework was developed to reconstruct pavement macrotexture in three dimensions and compute mean profile depth (MPD). Ground-control-based measurements agreed with a reference laser scanner within 15% across all test locations. A high-speed prototype using industrial cameras and a real-time kinematic positioning system was built. It was able to collect data up to 35 mi/hr and perform 3D reconstruction on cloud environments, increasing processing speed. The prototype was validated against a laser scanner at a controlled test track. The results demonstrated that contactless texture measurement and friction prediction are feasible and provide a foundation for more frequent, lower-cost monitoring of pavement surface characteristics, supporting proactive pavement management, safety screening, and more cost-effective maintenance decisions. The developed device measures texture and estimates friction for $61/mile, about 65% less than the $140/mile needed to collect both with current methods, and it costs only $73,500 to buy, compared with about $1,100,000 for a combined laser scanner and a transverse profiler. In addition, a data-driven model was developed to predict sideways friction measured by a Sideway-force Coefficient Routine Investigation Machine using pavement texture, traffic, roadway geometry, operating speed, and surface temperature. Three datasets collected in Florida and Illinois were used to evaluate the influence of dataset size, available features, and data distribution. Among the tree-based ensemble models evaluated, the Extra Trees model performed best, explaining approximately 85% of the variance, with MPD, traffic, operating speed, and surface temperature identified as the most influential variables. Finally, a finite element framework coupling a 3D tire model, texture-based friction model, and water film was developed to evaluate hydroplaning. The framework demonstrated that coarser macrotextures resulted in relatively better tire-pavement contact at higher speeds because of their improved surface drainage capacity.