The paper contributes towards the modeling, identification, and control of model jet engines. We propose a nonlinear, second order model in order to capture the model jet engines governing dynamics. The model structure is identified by applying sparse identification of nonlinear dynamics, and then the parameters of the model are found via gray-box identification procedures. Once the model has been identified, we approached the control of the model jet engine by designing two control laws. The first one is based on the classical Feedback Linearization technique while the second one on the Sliding Mode control. The overall methodology has been verified by modeling, identifying and controlling two model jet engines, i.e. P100-RX and P220-RXi developed by JetCat, which provide a maximum thrust of 100 N and 220 N, respectively.
19 November 2021 in IEEE Robotics and Automation Letters
Effective control design of flying vehicles requires a reliable estimation of the propellers’ thrust forces to secure a successful flight. Direct measurements of thrust forces, however, are seldom available in practice and on-line thrust estimation usually follows from the application of fusion algorithms that process on-board sensor data. This letter proposes a framework for the estimation of the thrust intensities on flying multibody systems that are not equipped with sensors for direct thrust measurement. The key ingredient of the proposed framework is the so-called centroidal momentum of a multibody system, which combined with the propeller model. It enables the design of Extended Kalman Filters (EKF) for on-line thrust estimation. The presented approach tackles the additional complexity in thrust estimation due to the possibly large number of degrees of freedom of the system and uncertainties in the propeller model. For instance, a covariance scheduling approach based on the turbines RPM error is proposed to ensure a reliable estimation even in case of turbine failures. Simulations are presented to validate the proposed algorithm during robot flight. Moreover, an experimental setup is designed to evaluate the accuracy of the estimation algorithm using iRonCub, a jet-powered humanoid robot, while standing on the ground.
11 November 2024 in IEEE Robotics and Automation Letters
This paper presents XBG (eXteroceptive Behaviour Generation), a multimodal end-to-end Imitation Learning (IL) system for whole-body autonomous humanoid robots used in real-world Human-Robot Interaction (HRI) scenarios. The main contribution is an architecture for learning HRI behaviours using a data-driven approach. A diverse dataset is collected via teleoperation, covering multiple HRI scenarios, such as handshaking, handwaving, payload reception, walking, and walking with a payload. After synchronizing, filtering, and transforming the data, we show how to train the presented Deep Neural Networks (DNN), integrating exteroceptive and proprioceptive information to help the robot understand both its environment and its actions. The robot takes in sequences of images (RGB and depth) and joints state information to react accordingly. By fusing multimodal signals over time, the model enables autonomous capabilities in a robotic platform. The models are evaluated based on the success rates in the mentioned HRI scenarios and they are deployed on the ergoCub humanoid robot. XBG achieves success rates between 60% and 100% even when tested in unseen environments.
This article takes a step to provide humanoid robots with adaptive morphology abilities. We present a systematic approach for enabling robotic covers to morph their shape, with an overall size fitting the anthropometric dimensions of a humanoid robot. More precisely, we present a cover concept consisting of two main components: a skeleton, which is a repetition of a basic element called node, and a soft membrane, which encloses the cover and deforms with its motion. This article focuses on the cover skeleton and addresses the challenging problems of node design, system modeling, motor positioning, and control design of the morphing system. The cover modeling focuses on kinematics, and a systematic approach for defining the system kinematic constraints is presented. Then, we apply genetic algorithms to find the motor locations so that the morphing cover is fully actuated. Finally, we present control algorithms that allow the cover to morph into a time-varying shape. The entire approach is validated by performing kinematic simulations with four different covers of square dimensions and having $3\times 3$, $4\times 8$, $8\times 8$, and $20\times 20$ nodes, respectively. For each cover, we apply the genetic algorithms to choose the motor locations and perform simulations for tracking a desired shape. The simulation results show that the presented approach ensures the covers to track a desired shape with good tracking performances.
This paper introduces a Data-Fused Model Predictive Control (DFMPC) framework that combines physics-based models with data-driven representations of unknown dynamics. Leveraging Willems’ Fundamental Lemma and an artificial equilibrium formulation, the method enables tracking of changing, potentially unreachable setpoints while explicitly handling measurement noise through slack variables and regularization. We provide guarantees of recursive feasibility and practical stability under input–output constraints for a specific class of reference signals. The approach is validated on the iRonCub flying humanoid robot, integrating analytical momentum models with data-driven turbine dynamics. Simulations show improved tracking and robustness compared to a purely model-based MPC, while maintaining real-time feasibility. Code: https://github.com/ami-iit/papergorbanielobaid2025lcssdfmpc-ironcub.
This paper presents a Non-Linear Model Predictive Controller for humanoid robot locomotion with online step adjustment capabilities. The proposed controller considers the Centroidal Dynamics of the system to compute the desired contact forces and torques and contact locations. Differently from bipedal walking architectures based on simplified models, the presented approach considers the reduced centroidal model, thus allowing the robot to perform highly dynamic movements while keeping the control problem still treatable online. We show that the proposed controller can automatically adjust the contact location both in single and double support phases. The overall approach is then tested with a simulation of one-leg and two-leg systems performing jumping and running tasks, respectively. We finally validate the proposed controller on the position-controlled Humanoid Robot iCub. Results show that the proposed strategy prevents the robot from falling while walking and pushed with external forces up to 40 Newton for 1 second applied at the robot arm.