19 July 2021 in Applied Physics Letters
It is an urgent requirement to suppress surface partial discharge (PD) activities of dielectrics for modern electrical and electronic devices. Here, we introduce a method to mitigate the surface PD in a manner of tailoring insulation surface conductivity. A surface coating with a conductivity ranging from 10−13 to 10−10 S is developed to regulate the surface charge migration in the vicinity of the triple junction and to suppress effectively the surface PD activity. The excellent performance of this coating provides an approach for surface PD suppression at DC voltage, which has great application potential in the insulation design of DC electric power equipment, DC generators, power electronic devices, printed circuit board (PCB) layout, and various integrated electrostatic sensors and actuators.
1 March 2022 in Composites Science and Technology
12 October 2020 in IEEE Access
The innovation of materials with disruptive properties can be efficiently guided by improved physical understanding of material design principles. The design of a polymeric insulation depends on the desired requirements of the specific application, which, in the case of DC cable insulation, can be stated in terms of the following properties: controlled electrical conductivity, low space charge accumulation and high breakdown strength. Full characterization and detailed understanding of these properties as well as their correlation and balance may bring the ability to engineer needed dielectric properties for using as DC cable insulation. The aim of this paper is to identify the optimal DC insulation design space and to develop a formalism of the correlation between the conductivity and space charge, guided by a relatively simple model based on two physical parameters, activation energy (ξ) and mean trap separation (λ). With respect to implications for practical material design, the study demonstrates that a polymer material with activation energies in the range of 0.4 to 0.5 eV with relatively high trap density (N) (N= λ-3 , λ=1nm, N=1E+27 m-3) can be suitable for HVDC cable insulation.
28 May 2024 in IEEE Access
PCB layouts with different polygon shapes and insulation distances were prepared and their surface flashover voltage subjected to different ramping rates were measured at different temperatures and different low gas pressures for emulated high-altitude conditions. The dependence of the surface flashover voltage on effects of gas pressure, surface insulation distance, temperature, and polygon shape was studied. Modulation efforts which include tailoring the local surface conductivity and local topography modification were performed to increase the flashover of PCB, and the related mechanism was studied. The results showed that the voltage ramping rate plays an important role in determining flashover voltage. The flashover voltage is lower when the sample is subjected to a rapid voltage ramping rate than with a slow ramping rate. This phenomenon is more prominent towards ambient pressure. The increase in temperature results in a decrease in flashover voltage at 100 kPa, while at 20 kPa and 10 kPa, the influence of temperature on flashover becomes less significant. Through-holes designed in the PCB have a positive role in increasing flashover voltage at lower pressures. However, at 100 kPa, the holes no longer contribute to any higher flashover voltage. Modification of local surface conductivity has no contribution in increasing the flashover voltage, while a surface coating with a surface conductivity of 10 -10 S dramatically decreases the flashover voltage. The work presented in this paper provides a reference for the design and modification of PCB layouts for use in future aerospace hybrid propulsion systems.
11 September 2024 in IEEE Access
Aircraft electrification poses new challenges to the safe design of the insulation system under harsh operating conditions. This study focuses on the investigation of electrical treeing, a precursor to electrical breakdown in the bulk of electric wire and cables, under emulated low pressure and high temperature for high density electrification at high altitude. It was found in a model insulation of cross-linked polyethylene (XLPE) that low pressure and high temperature significantly decreased the treeing initiation voltage and increased tree growth propagation rate. Moreover, the presence and size of artificial air gap affected tree morphology, growth rate, and fractal dimension in a way that decreases insulation durability. The effect of pressure on treeing growth was studied by using the partial discharge (PD) measurements, which suggested lower pressure increased PD activities, with respect to the rate and magnitude of PDs during both stages of treeing initiation and propagation. This work could be used as a baseline for studying electrical treeing phenomenon at high altitudes with coupled high temperature-low pressure, to pave the way for the reliable design of insulation systems on the path towards aircraft electrification.
22 August 2022 in Journal of Applied Physics
A model DC material based on ethylene propylene rubber (EPR) including the pure EPR and the EPR-based nanodielectrics incorporated with two different nanoclays, Kaoline and Talc, under operational conditions was investigated. The operational conditions include a 20 kV/mm electric field at 25 °C, a 20 kV/mm electric field at 50 °C with a thermal gradient, and a 40 kV/mm electric field at 50 °C with a thermal gradient and polarity reversal. Space charge distribution, surface potential, and electrical conductivity were measured to characterize the model DC material and interpret the discrete charge dynamics in the bulk and at the interface of the three samples. The experimental results revealed that the electrical conductivity of Talc-filled nanodielectric has the least dependency on electric field and temperature, which reduces the conductivity gradient across the dielectric. Moreover, the successful suppression of space charge and the lower dielectric time constant in the Talc-filled nanodielectric result in a tuning electric field in the bulk not only under normal operating conditions but also more importantly under polarity reversal conditions. The maximum of absolute charge density decreases from 10.6 C/m3 for EPR to 2.9 C/m3 for the Talc-filled nanodielectric under 40 kV/mm with polarity reversal and at 50 °C with the thermal gradient. The maximum of local electric field enhancement for the mentioned condition reduces significantly from 97 kV/mm, 142% enhancement, for EPR to 45 kV/mm, only 12.5% enhancement, for the Talc-filled nanodielectric.