4 April 2022 in Materials Advances
A self-assembled two-dimensional montmorillonite nanocoating enables significantly enhanced corona resistance in the Kapton film.
26 July 2022 in Materials Advances
Thermally conductive polymers are highly desired as electrical insulation materials in power-electronic and electrical machines toward high power density and payload efficiencies. This paper investigates the thermal conductivity of hybrid epoxy composites containing talc nanoclay, boron nitride (BN) clusters, and zinc oxide (ZnO) particles using the Design of Experiment (DoE) approach. A statistical model of the composite thermal conductivity based on the compositions of the components has been established with an R-squared of 98.17%. The effects of shapes, sizes, filler thermal conductivity, and the structured network of the fillers are discussed. The structured edge-connecting BN nanosheets endowed in nanostructured BN-clusters play a critical role in composite thermal conductivity enhancement. The thermal conductivity with the optimized formulation could reach 1.3 W m−1 K−1, which is 6× higher than that of neat epoxy resin, while maintaining superior dielectric properties. The results of DoE analysis can be widely applied to the design of polymer composites with optimal formulations.
11 September 2024 in IEEE Access
Aircraft electrification poses new challenges to the safe design of the insulation system under harsh operating conditions. This study focuses on the investigation of electrical treeing, a precursor to electrical breakdown in the bulk of electric wire and cables, under emulated low pressure and high temperature for high density electrification at high altitude. It was found in a model insulation of cross-linked polyethylene (XLPE) that low pressure and high temperature significantly decreased the treeing initiation voltage and increased tree growth propagation rate. Moreover, the presence and size of artificial air gap affected tree morphology, growth rate, and fractal dimension in a way that decreases insulation durability. The effect of pressure on treeing growth was studied by using the partial discharge (PD) measurements, which suggested lower pressure increased PD activities, with respect to the rate and magnitude of PDs during both stages of treeing initiation and propagation. This work could be used as a baseline for studying electrical treeing phenomenon at high altitudes with coupled high temperature-low pressure, to pave the way for the reliable design of insulation systems on the path towards aircraft electrification.
4 August 2025 in Applied Physics Letters
Conductive Atomic Force Microscopy (C-AFM) was used to investigate if conductive by-products exist within surface tracks—closely related to electrical trees—that are generated by high-power surface flashover events on epoxy nanocomposites used in high-breakdown dielectric applications. Here, we show that topography measurements alone are insufficient to identify conductive surface tracks unambiguously. Instead, by mapping DC currents flowing into the sample from the scanned C-AFM tip, conductive tracks up to three orders of magnitude less resistive than adjacent epoxy nanocomposite material are revealed. Ohmic behavior was confirmed by systematically incrementing the applied voltage, thereby providing a unique method for directly quantifying and mapping the conductivity in electrical breakdown-induced surface tracks, with potential for future applications to the investigation of bulk electrical trees.
12 August 2024 in IEEE Access
This study combines comprehensive analyses of design parameters with encapsulation solutions of Direct Copper Bond (DCB) substrates used in high voltage power converter modules, focusing on partial discharge (PD) activity under varying pressures for aerospace applications. A detailed PD investigation on triple junction points as the main culprit of the failure in power electronics was conducted, examining the design and material aspects through experimental and simulation analysis. PD initiation and extracted information are presented for three common pad geometries on two types of substrates (AlN and G-10/FR4). The results reveal better performance of the AlN that has higher permittivity, i.e., 20-30% and 10-20% higher PD inception voltage (PDIV) than G-10/FR4 at ambient and low pressures, respectively, and 40-65% lower PDIV at low pressures due to the higher rate of gas ionization compared to the ambient pressure. The study also explores the impact of pad geometric design such as corner smoothness and spacing on electric field intensity, with an introduced pressure- and temperature-dependent ionization model coupled with 3D finite element model to quantify the impact of the pressure on the gas ionization and PD initiation. Furthermore, an extensive experimental and numerical study of PD on liquid and gel encapsulated DBC substrates at ambient and low pressures was also conducted. Two silicone gels (Dowsil™ 3-4170 and Sylgard™ 527) and one refrigerant dielectric liquid (fluorinert FC40) were investigated as encapsulating dielectrics for high voltage applications. The results reveal that different silicone gels, despite similar dielectric properties, can exhibit drastically different PD resistance due to intrinsic bulk properties and self-healing capabilities, outperforming liquid-based encapsulants. This highlights the significance of dielectric fluid and gel insulations characteristics to the performance of HV modules for aerospace applications.