Paolo Frigerio

Paolo Frigerio

Auto-generated profile, based on publicly available information

Paolo Frigerio

Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
28 January 2021 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
PFPaolo Frigerio
Paolo Frigerio
BDBianca Di Diodoro
Bianca Di Diodoro
VRValeria Rho
Valeria Rho
RCRoberto Carminati
Roberto Carminati
NBNicolò Boni
Nicolò Boni
GLGiacomo Langfelder
Giacomo Langfelder
This work presents a long-term characterization of a newly designed microelectromechanical-system (MEMS) micromirror capable of achieving a field-of-view (FOV) of almost 94°. The process used to fabricate the device allows to combine piezoelectric (PZT) actuation and piezoresistive (PZR) sensing of the tilt angle, enabling testing under closed loop control. Consistently with the adopted design guidelines, which considered fatigue limits on the silicon springs, the tested devices are able to withstand up to 3.6 billion continuous operating cycles in an uncontrolled laboratory environment when operated in resonant mode at 500 Hz. [2020-0366]

3 August 2020 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
GMGiorgio Mussi
Giorgio Mussi
PFPaolo Frigerio
Paolo Frigerio
GGGabriele Gattere
Gabriele Gattere
GLGiacomo Langfelder
Giacomo Langfelder
This article presents a real-time clock (RTC) system based on a microelectromechanical system (MEMS) resonator coupled to an integrated circuit (IC) that implements a frequency-compensating machine. The MEMS resonator is built with a standard, industrial-grade polysilicon process characterized by a -30-ppm/K linear temperature coefficient of frequency (TCf) and the frequency-drift compensation is entirely carried out within the IC using a fractional frequency division. The large, but deterministic, output jitter (≈1 μ s rms ) is then suppressed down to less than 40 ns rms with a low-power digital-to-time converter (DTC), whose usefulness in this kind of application is then analyzed. With a single-point temperature calibration, a ±8-ppm output frequency stability is demonstrated at ≈800-nA current consumption from a 1.2-V supply.

17 May 2022 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
PFPaolo Frigerio
Paolo Frigerio
LMLuca Molinari
Luca Molinari
ABAndrea Barbieri
Andrea Barbieri
MZMarco Zamprogno
Marco Zamprogno
GMGianluca Mendicino
Gianluca Mendicino
GLGiacomo Langfelder
Giacomo Langfelder
This article discusses the challenges in implementing a fully electrical closed-loop control system for high-end applications of quasi-static microscanners, accounting at the same time for wide aperture, high accuracy, and wide bandwidth. The discussion highlights how not only the ringing of the main mode but also the presence of spurious modes and nonlinearity impacts the closed-loop stability and accuracy. A novel control approach based on nested loops is conceived and implemented in the digital domain in a mixed-signal application-specific integrated circuit (ASIC). The developed versatile ASIC is designed to be coupled to different types of micromirrors, with fundamental frequency ranging from few hundred hertz to few kilohertz, by simply adjusting coefficients in the digital domain. The ASIC is here successfully operated with two micromirrors, and results demonstrate sawtooth position control at 28–32 $^\circ$ field of view and up to 120-Hz refresh rate, while holding at the same time a tilt angle resolution of 25 m $^\circ$ rms (dynamic range of 60 dB) and a linearity error below $\pm$ 1%.

10 March 2022 in IEEE Sensors Letters
Verified
Journal Article
Closed access
PFPaolo Frigerio
Paolo Frigerio
RCRoberto Carminati
Roberto Carminati
LMLuca Molinari
Luca Molinari
GLGiacomo Langfelder
Giacomo Langfelder
The paper presents a comparative study concerning the characterization of piezoresistive (PZR) and piezoelectric (PZT) tilt-angle sensing in MEMS micromirrors. Position tracking is mandatory in such devices, so to achieve high-resolution displays, and the control system must be accurate against noise sources and stable against drifts of physical parameters, such as ambient temperature. This work presents the performance results achieved on PZR and PZT sensors integrated on the same micromirror, showing that, at the cost of a larger area occupation, the latter achieves 10 times larger sensitivity (with improvements in the signal-to-noise ratio and thus in position accuracy), and a 5 times lower overall transduction variation under temperature changes.

5 October 2022 in Journal of Microelectromechanical Systems
Verified
Journal Article
Closed access
CPChristian Padovani
Christian Padovani
RNRiccardo Nastri
Riccardo Nastri
LPLeonardo Gaffuri Pagani
Leonardo Gaffuri Pagani
PFPaolo Frigerio
Paolo Frigerio
FRFrancesco Rizzini
Francesco Rizzini
GLGiacomo Langfelder
Giacomo Langfelder
This work advances the research on continuous mode-reversal frequency modulated accelerometers by characterizing in depth some of their nonidealities, proposing methods for their compensation, and exploiting a renovated sensor design that enables closed-loop compensation of shock and vibrations. The scale factor nonlinearity is first investigated and compensated through a cubic calibration term, yielding a 50% larger range for a 2.5-fold larger scale factor than in former implementations. Additionally, temperature effects on the zero-g offset are compensated by exploiting the value of the low-pass filtered resonance frequency, which yields a valuable information of the silicon sensor temperature. This enables reducing the zero-g-offset temperature dependence by a factor 5 over previous works on similar structures. Finally, a closed-loop compensation of the quality factor, implemented through additional driving electrodes in the structure, guarantees a 25-fold reduction on effects of shocks and vibrations exciting the acceleration-sensitive mode.2022-0117

23 October 2023 in IEEE Sensors Letters
Verified
Journal Article
Closed access
MPMarco De Pace
Marco De Pace
PFPaolo Frigerio
Paolo Frigerio
CVCarlo Valzasina
Carlo Valzasina
LFLuca Falorni
Luca Falorni
PPPietro Peliti
Pietro Peliti
GLGiacomo Langfelder
Giacomo Langfelder
The research on high-end microelectromechanical system (MEMS) gyrosco-pes often ignores the possibility still offered by the well-known mode-split architecture. This letter analyses how a yaw MEMS gyroscope commercialized for automotive applications can be practically readapted, by changing specific operating parameters, and above all, the electronics and phase calibration settings, in order to achieve consistent improvements. While holding the same full-scale range, a factor 15 in noise (0.05 °/√hr) and a factor 50 in stability (0.18 °/hr) are obtained with respect to the initial values, closely in line with prediction of the theoretical analysis.