Giorgio Mussi

Giorgio Mussi

Auto-generated profile, based on publicly available information

Giorgio Mussi

Dipartimento di Elettronica, Informazione e Bioingegneria, Politecnico di Milano, Milan, Italy

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 November 2017 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
PMPaolo Minotti
Paolo Minotti
SDStefano Dellea
Stefano Dellea
GMGiorgio Mussi
Giorgio Mussi
ABAndrea Bonfanti
Andrea Bonfanti
SFStefano Facchinetti
Stefano Facchinetti
GLGiacomo Langfelder
Giacomo Langfelder
This paper reports the developments toward an integrated, tri-axial, frequency-modulated, consumergrade, and microelectromechanical system (MEMS) gyroscope. A custom low-power (160 μA), low-phase-noise integrated circuit is designed specifically for frequencymodulated operation. Both yawand pitch-rate sensing systems are demonstrated by coupling the circuit with two novel micromachined structures fabricated with a 24-μmthick industrial process. In operation, both gyroscopes show a repeatable and stable scale factor, with less than 0.55% of part-to-part variability, obtained with no any calibration, and 35 ppm/°C of variability over a 25-70 °C temperature range.

3 August 2020 in IEEE Transactions on Ultrasonics, Ferroelectrics, and Frequency Control
Verified
Journal Article
Closed access
GMGiorgio Mussi
Giorgio Mussi
PFPaolo Frigerio
Paolo Frigerio
GGGabriele Gattere
Gabriele Gattere
GLGiacomo Langfelder
Giacomo Langfelder
This article presents a real-time clock (RTC) system based on a microelectromechanical system (MEMS) resonator coupled to an integrated circuit (IC) that implements a frequency-compensating machine. The MEMS resonator is built with a standard, industrial-grade polysilicon process characterized by a -30-ppm/K linear temperature coefficient of frequency (TCf) and the frequency-drift compensation is entirely carried out within the IC using a fractional frequency division. The large, but deterministic, output jitter (≈1 μ s rms ) is then suppressed down to less than 40 ns rms with a low-power digital-to-time converter (DTC), whose usefulness in this kind of application is then analyzed. With a single-point temperature calibration, a ±8-ppm output frequency stability is demonstrated at ≈800-nA current consumption from a 1.2-V supply.

5 September 2019 in IEEE Transactions on Industrial Electronics
Verified
Journal Article
Closed access
GMGiorgio Mussi
Giorgio Mussi
MBMarco Bestetti
Marco Bestetti
Valentina ZegaValentina Zega
Valentina Zega
Attilio FrangiAttilio Frangi
Attilio Frangi
GGGabriele Gattere
Gabriele Gattere
GLGiacomo Langfelder
Giacomo Langfelder
Epitaxial polysilicon is a cheap material that has been used in the MEMS industry for a long time. Its relatively large -30 ppm/K Temperature Coefficient of frequency (TCf) has prevented its widespread use in real-time clock (RTC) applications. This work investigates the possibility to use this material to build resonators to be used in real-time clock applications, starting from the assumptions that the TCf of polySilicon is large but very repeatable. This would allow a large manufacturer to use a time-saving, thus inexpensive, family compensation, where the calibration procedure is computed for a very small fraction of the population of produced RTCs and then applied to the entire production output. This work presents a novel design of capacitive resonators for RTCs and demonstrates that the spread of the part-to-part temperature dependence is low enough to allow an electronic family compensation to within ±20 ppm of the output frequency.

8 August 2017 in Proceedings
Verified
Conference Paper
Open access
PDF file
Valentina ZegaValentina Zega
Valentina Zega
PMPaolo Minotti
Paolo Minotti
GMGiorgio Mussi
Giorgio Mussi
ATAlessandro Tocchio
Alessandro Tocchio
LFLuca Falorni
Luca Falorni
Alberto CoriglianoAlberto Corigliano
Alberto Corigliano
In this work, the mechanical design and the experimental validation of a micro-electromechanical frequency-modulated (FM) pitch gyroscope are presented. The proposed device is fabricated through the ThELMA © surface micromachining process of STMicroelectronics and it represents, to the authors’ knowledge, the first small-footprint (690 µm × 946 µm) prototype of FM gyroscope able to measure an in-plane angular rate. The measured scale factor, defined as the mean angular gain, equals 0.973 Hz/Hz, in close agreement with theoretical predictions. It depends only on the mass distribution in the mechanical structure and is, consequently, not influenced by environmental fluctuations.

1 April 2019
Verified
Conference Paper
Closed access
GMGiorgio Mussi
Giorgio Mussi
PFPaolo Frigerio
Paolo Frigerio
GLGiacomo Langfelder
Giacomo Langfelder
GGGabriele Gattere
Gabriele Gattere
Real-Time Clocks (RTC) based on a microelectromechanical system (MEMS) resonator are typically affected by a large frequency drift across the temperature range. To overcome this problem, digital circuitry is commonly employed to compensate for the thermal effects at the expense of a significant increase in output jitter which should be filtered with a PhaseLocked Loop (PLL). In this work, it is presented an alternative approach to jitter suppression where a Digital-to-Time Converter (DTC) removes the predominant deterministic portion of the output jitter, so to reduce consumption, area and complexity of the jitter-filtering blocks. Simulations in a 130 nm process show a 140 nA consumption from a 0.8 V power supply, with a reduction of the output rms period jitter from 944 ns to 31 ns.