12 August 2020 in IEEE Transactions on Microwave Theory and Techniques
This article presents the theory and design methodology of broadband RF-input continuous-mode load-modulated balanced power amplifier (CM-LMBA) by introducing the CM output-matching networks in the LMBA architecture. It is illustrated that the CM impedance condition can be achieved by properly adjusting the phase difference between the different PA branches in the proposed CM-LMBA during the entire load modulation process. An RF-input CM-LMBA with 1.45-2.45-GHz bandwidth using commercial GaN transistors is designed and implemented to validate the proposed architecture. The fabricated CM-LMBA attains a measured 11.2-13.4-dB gain and around 40-W saturated power. Power-added efficiency (PAE) of 46.4%-56.5% and 43.2%-50.3% is achieved at 6- and 8-dB output power back-offs throughout the designed band. When driven by a 100-MHz OFDM signal with an 8-dB peak-to-average power ratio (PAPR), the proposed CM-LMBA achieves better than -46-dBc adjacent channel leakage ratio (ACLR) and higher than 45% average PAE after digital predistortion at 1.8 and 2.1 GHz.
2 February 2022 in IEEE Journal of Solid-State Circuits
This article presents a broadband fully integrated Doherty power amplifier (DPA) using a continuous-mode combining load. It is illustrated that the continuous-mode impedance condition in back-off and saturation for Doherty operation can be achieved with a simple impedance inverter network (IIN) that can be realized using lumped components in gallium nitride (GaN) monolithic microwave integrated circuits (MMICs). A DPA was designed and fabricated using the 250-nm GaN process to validate the proposed architecture and design methodology. The fabricated DPA chip attains around 8 W saturated power from 4.1 to 5.6 GHz. About 38.5%–46.5% drain efficiencies are achieved at 6-dB output power back-off within the entire design band. When driven by a 100-MHz OFDM signal with 6.5-dB peak-to-average power ratio (PAPR), the proposed DPA achieves better than −45-dBc adjacent channel leakage ratio (ACLR) and higher than 38% average efficiency at 4.4 and 5.2 GHz after digital predistortion.
11 November 2021 in IEEE Transactions on Microwave Theory and Techniques
This article presents a novel waveform engineered sequential load modulated balanced amplifier (W-SLMBA) that uses a continuous Class-F −1 control amplifier (CA) to manipulate the impedance trajectory of the balanced amplifier (BA). It is demonstrated that the use of the continuous Class-F −1 CA can trigger a unique impedance load modulation mechanism by which the fundamental impedance of the BA is shaped by the varying second-harmonic load reactance of the CA. Theoretical derivations reveal that this special load modulation yields extended design space for the LMBA, in which high efficiency can be achieved over wide bandwidth and output power back-off (OPBO). A prototype operating from 1.80 to 2.75 GHz is designed following the proposed theory. The implemented LMBA achieves a measured drain efficiency (DE) of 60.2%–68.3% at saturation and 51.8%–69.0% at 8-dB OPBO. When tested with a 100-MHz long-term evolution (LTE) signal having peak-to-average power ratio (PAPR) of 8 dB, the proposed LMBA achieves 50.2%–59.1% average DE and better than −45.1-dBc adjacent channel power ratio (ACPR) across the target bandwidth after digital predistortion (DPD).
12 December 2022 in IEEE Transactions on Microwave Theory and Techniques
This article presents the design methodology of a broadband radio frequency (RF)-input sequential load modulated balanced amplifier (SLMBA) with extended high-efficiency design space, by introducing the second-harmonic load manipulation over an enlarged range for the control amplifier (CA). The extension of CA load design space not only can provide the time-domain-varying drain current waveform inside the entire design continuum but also allows maintaining high efficiency at output power back-off (OBO) over an extended operation bandwidth. To validate the theory, a broadband SLMBA operating at 2.05–3.65 GHz was designed and fabricated using packaged gallium nitride (GaN) transistors. The implemented power amplifier (PA) attains a measured 45.2–46.8-dBm peak output power. Drain efficiency (DE) of 61.2%–79.7% at saturation and 50.5%–66.2% at 8-dB OBO is achieved throughout the designed bandwidth. When tested with a 100-MHz long-term evolution (LTE) signal with a peak-to-average-power ratio (PAPR) of $8$ dB, the proposed SLMBA achieves 50.7%–63.5% average DE over 2.05–3.55 GHz and better than $-$ 45.1 dBc adjacent channel power ratio (ACPR) after digital predistortion (DPD).
1 December 2022 in IEEE Transactions on Microwave Theory and Techniques
This article presents a new class of power amplifier (PA), designated as Class-iF $-$ 1 , that utilizes input harmonics to achieve high efficiency with enhanced linearity performance beyond the conventional Class-F $-$ 1 PA. The amplitude-to-amplitude modulation (AM/AM) profile of the conventional Class-F $-$ 1 PA is mathematically modeled as a function of the input drive level, such that the occurrence of inflection points can be investigated. Theoretical derivation shows that the appropriate utilization of input nonlinearity poses a solution to rectify the double inflection characteristics of the conventional Class-F $-$ 1 PA, which, consequently, can be realized by proper manipulation of second harmonic source impedance ( $Z_\text{2S}$ ). The theoretical findings were validated with load—pull results at 2.3 GHz with a 2-mm gallium nitride (GaN) device, presenting enhanced linearizable output power and efficiency for the Class-iF $-$ 1 PA, with a broad second harmonic design space over the open-circuit region. As proof of concept, a Class-iF $-$ 1 PA was designed and fabricated, obtaining 40.1–40.8 dBm output power and 71.2%–77.3% drain efficiency (DE) performance at 3-dB gain compression level operating over 2.0–2.6-GHz frequency range. When tested with a 20-MHz 8.5-dB peak-to-average-power-ratio (PAPR) long-term evolution (LTE) signal, around 32.01-dBm average output power was attained at 2.3 GHz with an average DE of 34.59% and $-$ 56.05 dBc adjacent channel power ratios (ACPRs) after digital predistortion (DPD) correction.
27 July 2021 in IEEE Transactions on Microwave Theory and Techniques
To reduce the demand for frequently adjusting phase shifts in the fifth-generation (5G) multiple-input multiple-output (MIMO) beamforming transmitters, in this article, a novel digital predistortion (DPD) technique is proposed, which employs multiple predistortion boxes to shape the pattern of nonlinear distortions in space in order to linearize multiple targets simultaneously. By using this approach, the linearization angle is widened and thus the communication quality can be kept when the user moves off the main beam direction. As a proof of concept, two DPD boxes, namely main and auxiliary boxes, are used to realize the 2-target linearization. A new model extraction method is also proposed with a dedicated over-the-air (OTA) feedback post-processing stage. Simulation and experiment are demonstrated on a 4-path beamforming transmitter. The results show that the proposed DPD method can effectively widen the linearization angle with reasonable additional complexity.