Jiahui Yuan

Jiahui Yuan

Auto-generated profile, based on publicly available information

Jiahui Yuan

Key Laboratory of the Ministry of Education for Wide Band-Gap Semiconductor Materials and Devices, School of Microelectronics, Xidian University, Xian, China

Research Focus & Metrics

Academic Career Length

19Years (2008-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
10 February 2022 in IEEE Transactions on Electron Devices
Verified
Journal Article
Closed access
BDbaoxing duan
baoxing duan
JYJiahui Yuan
Jiahui Yuan
YWYandong Wang
Yandong Wang
LYLuoyun Yang
Luoyun Yang
Yintang YangYintang Yang
Yintang Yang
The traditional GaN high electron mobility transistor (GaN HEMT) is in the ON-state under zero gate bias, which does not meet the requirements of practical application. Therefore, in the application, it is necessary to continuously increase the negative voltage to the power grid to stop the equipment, which will increase the system cost and limit the improvement of system reliability. Therefore, the realization of enhanced AlGaN/GaN HEMT is of great significance. In order to further improve the breakdown characteristics and get a positive threshold voltage for GaN HEMT, a new enhance-mode junction AlGaN/GaN HEMT (EM-AlGaN/GaN JFET) structure is proposed in this article for the first time with the high breakdown voltage (BV) by introducing p-GaN buried layer into GaN epitaxial buffer layer to form p-n junction. The Sentaurus TCAD software is used to simulate the EM-AlGaN/GaN JFET. The simulation results show that the positive threshold voltage ( ${V}_{\text{th}}$ ) of 1.21 V is obtained, while the BV of the novel EM-AlGaN/GaN JFET is about 1283 V. The corresponding low-specific ON-resistance ${R}_{ \mathrm{\scriptscriptstyle ON},\text{sp}}$ is 2.44 m $\boldsymbol {\Omega } \cdot $ cm 2 . The switching device figure of merit (FOM) is further improved. The FOM of 679 MW $\cdot $ cm −2 (FOM = BV 2 / ${R}_{ \mathrm{\scriptscriptstyle ON},\text{sp}}$ ) is 1.52 times of the FOM (447 MW $\cdot $ cm −2 ) of conventional AlGaN/GaN HEMT. We can see that the introduction of p-GaN reduces the concentration of two-dimensional electron gas (2DEG) in the ON-state. In the OFF-state, the gate of the p-n junction forms a higher built-in potential and modulates the electric field distribution to get high BV. Due to the heterojunction polarized 2DEG, it has a lower ${R}_{ \mathrm{\scriptscriptstyle ON},\text{sp}}$ than the conventional GaN JFET. It has a good application prospect in the field of power electronic devices.

1 January 2008
Verified
Conference Paper
Closed access
JYJiahui Yuan
Jiahui Yuan
JCJohn Cressler
John Cressler
A peak fT of 325 GHz is achieved, for the first time, in a 130 nm, 200 GHz, 3rd-generation SiGe HBT technology at 300 K, by utilizing fT-doubler techniques. This speed enhancement is equivalent to gaining an additional generational node (from 3rd to 4th), with no underlying change to the transistor profile or lithography. The fT-doubler can be treated as a single transistor unit cell during circuit design, which is verified by the investigation of its small-signal equivalent circuit. Reduced Cpi is demonstrated to be the root origin of the fT-enhancement. The impact of emitter geometry on performance is investigated. A record fT of 438 GHz is achieved at 93 K.

1 September 2019
Verified
Conference Paper
Closed access
JLJia Liu
Jia Liu
QFQingqin Fu
Qingqin Fu
ZAZhengquan Ang
Zhengquan Ang
PXPingjiang Xu
Pingjiang Xu
YLYuhua Lu
Yuhua Lu
RNRui Nie
Rui Nie
This paper analyzes the shortcomings of two setting methods which is commonly used in security chip communication rate, and proposes an improved setting method. The basic communication rate instruction parameters are set in a security chip for setting the communication rate in different communication modes. The interface device sends the communication rate instructions to the security chip. The security chip executes the communication rate instructions so as to complete the setting of the communication rate. This method can switch the communication mode freely, so it can be applied to diversified application scenarios.