Ibsa Neme

Ibsa Neme

Auto-generated profile, based on publicly available information

Ibsa Neme

Department of Chemical Engineering, College of Biological and Chemical Engineering, Addis Ababa Science and Technology University, Addis Ababa, Ethiopia

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 December 2022 in Heliyon
Verified
Journal Article
Open access
INIbsa Neme
Ibsa Neme
GGGirma Gonfa
Girma Gonfa
CMChandran Masi
Chandran Masi
Low-cost and renewable adsorbent activated carbon from lignocellulosic biomass is a focus of worldwide concern due to its readily available waste disposal problems in the environment. Physical and chemical processes are the main procedures forproduction of biomass-activated carbon (AC). Activating lignocellulosic biomass by chemical methods in terms of energy performance, lower timecarbonization, and temperature is mutual forthe production of activated carbon. Out of chemical activating agents (H3PO4, H2SO4, ZnCl2, FeCl3, NaOH, KOH, and K2CO3), H3PO4 is the most commonly used chemical activating agent during the synthesis of activated carbon from lignocellulosic biomass because of its ease of recovery, low environmental impact, and higher carbon yield. The surface area of most activated carbon from lignocellulosic biomass by H3PO4was in the variability of 456.1–2806 m2/g, yielding 26.1–85 % and an extreme adsorption capacity of 2.5–89.29 mg/g. And also, high acids to precursor ratio and activation temperature of AC were synthesized from lignocellulosic biomass. Generally, the advantage of this review paper, gathers evidence from currently published articles deliberating chemical composition, proximate values, biomass activation methods, the elemental composition of lignocellulosic biomass, physio-chemical properties of different lignocellulosic materials AC synthesized using a phosphoric acid activation agent, and the usage of derived activated carbon through phosphoric acid activation for water disinfection, solute organic matter, energy storage, and heavy metal removal.

19 August 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
JKJ. Kumaraswamy
J. Kumaraswamy
VSVidyasagar Shetty
Vidyasagar Shetty
SSS. Sanman
S. Sanman
PNPremkumar Naik
Premkumar Naik
SSShabari Shedthi
Shabari Shedthi
INIbsa Neme
Ibsa Neme
Ni-Cu based alloy metal matrix nanocomposites are in great demand for advanced technological applications due to their high temperature, strength, and better thermal properties. The aim is to investigate the thermal conductivity and coefficient of thermal expansion of the nickel based alloy nanocomposites reinforced with titanium dioxide (TiO2) which varies from 3 to 12 weight % nanoparticulates (45 to 60 nm). The thermal conductivity was measured using a comparative cut bar method (ASTM E1225), and thermal expansion was analyzed using a push-rod dilatometer method (ASTM E228). From experimentation, it was observed that thermal conductivity of the nanocomposites activity increases with inclusion of the nanoparticles up to 9 weight % after descent due to the temperature effects in nanocomposites, and thermal expansion of the nanocomposites decreases with addition of the nanoparticles up to 9 weight % and further rises marginally due to ductility of composites. Due to the incorporation of hard ceramic particles into the matrix, the composites’ thermal conductivity increases to 57.42 W/m , and their thermal expansion decreases to 12 × 10−6. Nickel alloys are widely used in marine, automotive, valve, pump, and aircraft applications.

1 March 2023 in Case Studies in Chemical and Environmental Engineering
Verified
Journal Article
Open access
INIbsa Neme
Ibsa Neme
GGGirma Gonfa
Girma Gonfa
CMChandran Masi
Chandran Masi

19 July 2022 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
PAPrudhvi Krishna Amburi
Prudhvi Krishna Amburi
SGSenthilkumar Gnanamani
Senthilkumar Gnanamani
IMIbsa Neme Mogose
Ibsa Neme Mogose
The experimental research on heat transfer characteristics is an ever-ending scheme since the life of all thermoelectronic devices relies on the effective management of thermal energy. In some cases, the gradient of temperature for heat transfer is to be minimum to avoid energy loss, but also there are numerous applications where the requirement of heat transfer to be maximum and could be achieved with a higher temperature difference between the heat transfer medium. In our current research, distilled water-ethylene glycol heat transfer fluid (HTF) was tested with different inlet mass flow rates and temperature as the hot fluid. Atmospheric air was chosen as the cold fluid. The natural convection heat transfer rate between hot and cold fluid streams was analyzed with and without the generation of micronanobubbles in the hot fluid. It was observed that compared to the base heat transfer fluid, the nanobubbles heat transfer fluid resulted in a 10–12% increase in heat transfer rate at hot fluid inlet temperatures of 28°C, 30°C, 32°C, 34°C, and 36°C. The method of generation of nanobubbles in HTF and their behavior are also highlighted.

4 January 2023 in Advances in Materials Science and Engineering
Verified
Journal Article
Open access
PDF file
SMS. Meikeerthy
S. Meikeerthy
NEN. Ethiraj
N. Ethiraj
INIbsa Neme
Ibsa Neme
CMChandran Masi
Chandran Masi
Underwater friction stir welding (UWFSW) is an advancement of conventional friction stir welding, which is performed in air. The need for welding underwater calls for more information to be explored in the welding of different materials. The aim of this research is to investigate the UWFSW of 2 mm titanium sheet joints for their tensile and microstructural properties and compare them with the results of friction stir welding (FSW) performed in air. Also, nondestructive tests, such as radiography and dye penetrant tests, were carried out to identify the occurrence of any weld defects. The rotational speed of the FSW tool and its travelling speed were considered process parameters, while other parameters like the tilt angle of the tool, shape of the tool pin, etc. were kept constant. The results show that the welded joints with higher strengths were achieved at a lower travelling speed of 140 mm/min at a rotational speed of 400 and 500 rpm in FSW and UWFSW, respectively. The mechanical properties such as yield strength, tensile strength, and hardness are improved in UWFSW when compared with conventional FSW due to the proper mixing of the metal and effective cooling due to the water environment. In underwater FSW, the improved YS and TS values are observed, which are 95.9% and 75.1% of the base metal values, respectively, when the tool rotational speed is 400 rpm and the travelling speed is 140 mm/min. However, the elongation % is much lower in both FSW and UWFSW when compared with the base metal. These results are supported by microstructure and nondestructive test outcomes.