1 March 2008 in IEICE Transactions on Electronics
Digital superconductor electronics has been experiencing rapid maturation with the emergence of smaller-scale, lower-cost communications applications which became the major technology drivers. These applications are primarily in the area of wireless communications, radar, and surveillance as well as in imaging and sensor systems. In these areas, the fundamental advantages of superconductivity translate into system benefits through novel Digital-RF architectures with direct digitization of wide band, high frequency radio frequency (RF) signals. At the same time the availability of relatively small 4K cryocoolers has lowered the foremost market barrier for cryogenically-cooled digital electronic systems. Recently, we have achieved a major breakthrough in the development, demonstration, and successful delivery of the cryocooled superconductor digital-RF receivers directly digitizing signals in a broad range from kilohertz to gigahertz. These essentially hybrid-technology systems combine a variety of superconductor and semiconductor technologies packaged with two-stage commercial cryocoolers: cryogenic Nb mixed-signal and digital circuits based on Rapid Single Flux Quantum (RSFQ) technology, room-temperature amplifiers, FPGA processing and control circuitry. The demonstrated cryocooled digital-RF systems are the world's first and fastest directly digitizing receivers operating with live satellite signals in X-band and performing signal acquisition in HF to L-band at ∼30GHz clock frequencies.
27 May 2009 in IEEE Transactions on Applied Superconductivity
We describe several improvements that are being pursued to improve the dynamic range of lowpass phase modulation-demodulation (PMD) analog-to-digital converters (ADC). The existing ADC has been tested at sampling frequencies up to 29.44 GHz; a 89.15 dB signal to noise ratio (SNR) is achieved for a 10 MHz sinusoidal input, with the noise being measured in a reference 10 MHz bandwidth in the decimated band. The first improved approach involves a multi-rate ADC where the modulator sampling frequency is increased in multiples of the decimation filter clock. We have tested the multi-rate ADCs at sampling frequencies up to 46.08 GHz and 29.44 GHz for chips fabricated using the 4.5 and 1 kA/cm2 fabrication processes respectively. For a single channel ADC, with a 9.92 MHz sinusoidal input, sampled at 29.44 GHz, the SNR is 83.93 dB in a reference 10 MHz bandwidth. The spur-free dynamic range (SFDR) is 95 dB. In another improved architecture, called the quarter-rate ADC, the modified quantizer quadruples the input dynamic range by distributing the input in a cyclical fashion to four output channels, each operating at a quarter of the fluxon transport rate. This enables quadrupling the synchronizer channels, providing an opportunity for up to 12 dB performance enhancement. A parallel counter following the multi-channel synchronizer converts the differential code to a multi-bit binary code, which is further processed by the decimation filter. A prototype version of this ADC with a two channel synchronizer, fabricated using the 4.5 kA/cm2 process, has been tested up to a sampling frequency of 25.6 GHz. For a 10 MHz sinusoidal input, the SNR is 82.54 dB, with the noise measured in a reference 10 MHz bandwidth. We are also designing a subranging ADC with two PMD front-ends. Simulation results promise greater than 20 dB performance enhancement.
11 April 2019 in IEEE Transactions on Applied Superconductivity
Improving the efficiency in digital data transport, originating from 4 K superconductor integrated circuits (ICs) to standard room-temperature (300 K) electronics, both in terms of speed and power consumption, is vitally important for nearly all applications of superconductor digital electronics. The required data link must include all necessary amplification and conditioning to convert digital data from single flux quantum (SFQ) logic to standard CMOS logic levels. Therefore, one must minimize the overall power consumption for the required total data throughout by taking into account all parts of the link: 1) data transmitters or output drivers with SFQ input, 2) additional amplifiers, 3) transmission lines, and 4) data receivers at room-temperature, such as the ones available on commercial field-programmable gate arrays (FPGAs). Here, we describe two variants of electrical data links, with and without cryogenic semiconductor amplifiers.
24 January 2017 in IEEE Transactions on Applied Superconductivity
The MIT Lincoln Lab SFQ4ee and SFQ5ee process nodes, targeted at energy-efficient superconducting digital circuits, allow the fabrication of complicated multilayer circuit structures. Published per-length inductance values do not hold if ground plane (GP) and sky plane (SP) combinations are changed, or if inductance is distributed over multiple via-connected layers with current return paths determined by the specific placement of sky-to-ground vias. A three-dimensional inductance extraction tool, InductEx, can handle extraction from such complicated multilayer structures with holes in the GPs and SPs. We present calibrated parameter sets for InductEx generated from the analysis of twelve representative test structures. We show that the root-mean-squared-error (RMSE) between InductEx extractions and averaged experimental measurements of self-inductance are below 1% for several calibration sets-The lowest ever reported. The RMSE between calculations and measurements for mutual inductance is also below 1% for the best calibration set-A level also never achieved before.
3 March 2021 in IEEE Transactions on Applied Superconductivity
The Josephson balanced comparator, a decision-making circuit comprising two Josephson junctions (JJs) connected in series from a clocking perspective and in parallel for the current to be measured, is ubiquitous in single flux quantum (SFQ) logic. Its noise properties are crucial for the performance of logic devices. The characteristics of the balanced comparator can also be used to monitor fab process and design implementation as an indicator for excess noise, overheating, linearity, dynamic effects, etc. We designed several test structures to measure gray zone of various comparators fabricated in different nodes of process at MIT-LL. We used digital circuitry to measure comparator characteristics at low frequencies and an analog testbed to perform high frequency characterization. Experimental results for gray zone of comparators designed for fabrication nodes with different current densities, sheet resistances, critical damping are presented and studied as a function of clock frequency.
9 February 2021 in IEEE Transactions on Applied Superconductivity
HYPRES developed an advanced design flow and design infrastructure for single-flux-quantum (SFQ) superconductor integrated circuits using standard CMOS based EDA tools along with internally developed tools and has been successfully using this flow for the past several years. The design infrastructure includes the process design kit, advanced simulation methodology, and IC verification rule decks. The superconductor hierarchical circuit analyzer developed by HYPRES serves as bedrock of our simulation methodology facilitating circuit analysis and debugging including extraction of circuit parameter margins, analysis of Monte-Carlo simulations with process corners, as well as automated timing characterization. Using this proven design flow and infrastructure as a knowledge source, we have collaborated with Synopsys to enhance their tools for a full native tool enabled design flow and infrastructure, which represents a significant expansion in design capabilities and capacity for superconducting electronics. Using the 64-Bit arithmetic logic unit and a Pseudo Random Bit Sequence (PRBS) generator as reference circuits, we demonstrate the use of Synopsys tools for superconductor IC design including spice circuit simulations, plotting waveforms, margins analysis, Monte-Carlo simulations, HDL simulations with timing back-annotation, and IC validation including design rule checker and layout-versus-schematic checker.