Remote areas that are not within the maximum breakeven grid extension distance limit will not be economical or feasible for grid connections to provide electrical power to the community (remote area). An integrated autonomous sustainable energy system is a feasible option. We worked on a novel multi optimization electrical energy assessment/power management system of a microgrid network that adopted combined dispatch, load-following, and cycle-charging strategies (control system) that acted as a power interface module over the hybrid configuration of energy sources (grid network/downdraft biomass generator/solar photovoltaic), thermal load controller-boiler systems, and hybrid energy-storage technologies (lithium, iron flow, sodium sulfur, and flywheel) to enable the microgrid network to operate in the island (off grid), grid, and island-able (ability to isolate itself when it is connected to the grid network) modes efficiently and effectively. An optimal multitask control algorithm and the storage units of modeled power generation sources were executed with the HOMER software application to improve the energy system’s efficiency, promote effective storage management, minimize energy loss, and improve the lifespan of the microgrid network. The integrated energy system can work for both rural and urban areas.

The principal context of this study was a combined heat and power plant (CHPP) system, with the aim of conducting the multi-objective optimization (MOO) of an energy, exergy, and economic (3E) analysis. To meet rising energy demands, optimal operational conditions for CHPPs are required. Enhancements to plant equipment and improvements in plant design are critical. CHPP design has its basis in the first law of thermodynamics; the losses from such systems are therefore most accurately determined via exergy analysis. Energy quality can also be assessed using exergy analysis. Consequently, it is possible for the designers of thermodynamic systems to apply the findings to achieve improved efficiencies. The economic aspect of CHPP optimization is also critical because the structure is highly complex. This study therefore makes use of a Henry gas solubility optimization (HGSO) algorithm in a CHPP base case situation to achieve MOO. In this particular CHPP system, the respective enthalpy and exergy efficiencies were increased in the case of the boiler (7.22% and 7.21%), the turbogenerator (4.52% and 6.84%), and the condenser (3.06% and 31.37%). In this study, four scenarios are proposed, whereby the design of a heat exchanger network (HEN) aims to optimize energy savings and economic performance through analysis of the profits generated through electricity and steam production. A payback period of around two to three years was reported, where the cost increase under optimal conditions was found to be 0.3824%. The results demonstrate clearly that the tested techniques may be appropriate in practical scenarios when enhancing CHPP performance in the context of the base case.

The energy efficiency of a floating photovoltaic (FPV) system with a single azimuth-axis sun tracking mechanism is examined in this work. Installing FPV systems over water surfaces has several advantages, including easier rotation along a vertical axis, land conservation, and increased energy efficiency because of the water's natural cooling effect. Floating PV with Single-Axis Tracking (FPVSAT) is a novel feature of simple tracking for FPV that was proposed in this study. Since most conventional horizontal-axis tracking systems revolve around the horizontal N-S axis, single-axis trackers that spin around the vertical axis are somewhat unusual. The PV panels can follow the sun's azimuthal direction all day long the vertical-axis tracking design, which maximizes solar energy capture while preserving mechanical simplicity appropriate for floating buildings. Using experimental data from a prototype installed in Lop Buri, Thailand, a mathematical model was created and verified. We compared fixed, linear tracking, and vertical-axis azimuth tracking setups using simulations with high-resolution meteorological data. The azimuth tracking arrangement produces the maximum energy production, according to the results, highlighting the promise of vertical-axis tracking FPV systems as an affordable and scalable substitute for optimizing solar energy generation, especially in tropical areas with fluctuating sun patterns.

This experimental study aims at investigating on the performance of a high temperature solar water heating system. To approach the high temperature, a porous-medium concentrated solar collector equipped with a focused solar heliostat were proposed. The proposed system comprised of two parts: a 0.7x0.7-m² porous medium receiver, was installed on a 3-m tower, and a focused multi-flat-mirror solar heliostat with 25-m² aperture area. The porous medium used in this study was the metal swarf or metal waste from lathing process. To know how the system efficiency could be improved by using such porous medium, the proposed system with- and without-porous medium were tested and the comparative study was performed. The experimental results show that, using porous medium for enhancing the heat transfer mechanism, the system thermal efficiency was increased about 25%. It can be concluded that the efficiency of the proposed system can be substantially improved by using the porous medium.