The use of sensitive electronic devices has increased recently; hence, power quality has become an important factor in electrical power systems. The various disturbances occurring in the electrical network (harmonics, voltage swells, sags, etc.) may lead to technical-economic damage that negatively impacts the quality of the supplied power. Therefore, the use of the Unified Power Quality Conditioner (UPQC) is a promising solution to limit such damage. In this paper, a nine-level structure of the proposed standardized power quality conditioner is analyzed. The conditioner is connected between a photovoltaic system (UPQC-PV) and a smart grid. Then, a new approach to generate switches for the switches of both the series and parallel converters is proposed. This modulation technique relies on an adaptive hysteresis band (AHB) that is determined via a fuzzy logic controller in order to obtain the required modified output voltage with minimum distortion. Simulation results, using MATLAB/Simulink, of different disturbance scenarios that may occur in the network are presented to verify the accuracy of the proposed fuzzy-logic-based AHB control system. Compared with the conventional SPWM, it is found that the proposed AHB modulation technique significantly improves the power quality in terms of producing less total harmonic distortion in both the voltage and current waveforms.
The use of renewable resources for energizing the modern power systems has recently increased due to its sustainability and low operating costs. Photovoltaic (PV) system appears to be a good solution due to the fact that it can be established and operated locally. However, the maximum output power of these systems is usually achieved by using the maximum sun and power point (MPP) tracking techniques. This paper suggests a novel genetic algorithm (GA)-based technique to obtain the maximum output power of practical PV system located in the Latakia province of Syria. Based on this technique, azimuth and elevation angles of solar panels located in Latakia are first determined to track maximum radiation of the sun for every day of the whole year. After that, a GA-based technique is developed to track the maximum power point corresponding to maximum radiation during the year. Simulation results in MATLAB environment demonstrate the validation and effectiveness of the proposed GA-based technique to obtain the maximum generated power of the PV system. The results of this research can be easily adopted as a database reference to design the PV control system.
Power Electronics is the study of switching electronic devices and circuits to convert and control the flow of electrical energy. Power Electronics is the basic technology of switching power supplies, power converters, power inverters, motor drives, and motor soft starters. Inverters are devices that transform DC input into fixed AC output through changing the trigger angle, in the ideal statues the output wave form is perfect sine wave, however in the practical case it has some higher harmonics that need to be reduced. Inverters are an important part of UPS systems, fully explained in this chapter, where UPSs are uninterruptible Power Supply in which the inverters are included as an essential part, that can provide emergency power to a load when the input power source or main power source fails.
1 March 2020 in IOP Conference Series: Materials Science and Engineering
In this paper we will suggest equipment for a portable field hospital that is electrically fed by solar panels. The solar panel is connected to the removable (Portable) field hospital via an interface, which is an Interleaved Boost Converter (IBC). The analytical study is carried out for the traditional Boost Converter(BC) and the Interleaved Boost Converter (IBC) using Matlab/Simulink To ensure the electric supply of the portable field hospital with suitable voltage values. The paper will explain what might happen if we doubled or tripled the main elements of the conventional boost converter. The expected results will reflect the implementation importance of the interleaved converter (IBC) in comparison with conventional converter. We will also compare the different types of interleaved converter (IBC), so that we get the best interior connection of the IBC, which achieves the suitable distribution of the total current between the coils, as well as the best size – weight specifications. The selected IBC will contain less ripple in the output voltage waveform, where we provide the potable field hospital feed without disturbances or breakdowns, which cause the IBC to be out of serves or fault occurring to any part of it.
Most of the electric machines had a conventional design for speed –control. Previously, the speed regulation of these motors was done via traditional or mechanical contacts, for example: inserting resistors to the armature circuit or controlling the excited circuit of DC motor, and other methods of control. These classical methods, however, lead to non-linearity in mechanical or electromechanical characteristics [ω= f(M) or ω= f(I)], which in turn lead to increased power losses as the result of the non-soft regulation of speed, as well as the great inertia of classical control methods that rely on mechanical and electromagnetic devices.