Cihat Cagdas Uydur

Prof. Dr. Cihat Cagdas Uydur

Trakya University
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
20 March 2023 in Electric Power Systems Research
Verified
Journal Article
Closed access
OAOktay Arikan
Oktay Arikan
Cihat Cagdas UydurCihat Cagdas Uydur
Cihat Cagdas Uydur
CKCelal Fadil Kumru
Celal Fadil Kumru

1 March 2022 in Electric Power Systems Research
Verified
Journal Article
Closed access
OAOktay Arikan
Oktay Arikan
Cihat Cagdas UydurCihat Cagdas Uydur
Cihat Cagdas Uydur
CKCelal Fadil Kumru
Celal Fadil Kumru

12 October 2020 in Energies
Verified
Journal Article
Open access
PDF file
Cihat Cagdas UydurCihat Cagdas Uydur
Cihat Cagdas Uydur
OAOKTAY ARIKAN
OKTAY ARIKAN
It is known that the failure of cable terminations causes power outages and impairs system quality and continuity. Besides, serious economic losses on both the distribution and consumer sides occur. In this study, the dielectric behavior of the cable and the faults caused by the defects in the cable termination under overvoltage has been examined. As test samples, 12 kV XLPE insulated cable is used and they were aged at three (3*U0) and five (5*U0) times the rated voltage. After each aging cycle, dielectric parameters of the cable were measured by an OMIRCRON CPC100/CPTD1 device, and the partial discharge (PD) was measured by an OMICRON MPD600 device. In the measurements, it was observed that the cable was broken down at different aging cycle numbers as a result of defects in the cable termination due to weak workmanship. As a result of the measurements, it is concluded that defects in the cable termination give information about the increase in the probability of failure and the decrease of the cable lifetime. Consequently, it is concluded that fine workmanship and timely maintenance of cable terminations prevent the system from unwanted power outages and economic losses.

7 August 2022 in Electrical Engineering
Verified
Journal Article
Closed access
PDF file
Cihat Cagdas UydurCihat Cagdas Uydur
Cihat Cagdas Uydur
OAOKTAY ARIKAN
OKTAY ARIKAN

1 September 2018
Verified
Conference Paper
Closed access
Cihat Cagdas UydurCihat Cagdas Uydur
Cihat Cagdas Uydur
OAOktay Arikan
Oktay Arikan
OKOzcan Kalenderli
Ozcan Kalenderli
Electricity transmission with high voltage is usually done with overhead lines by using bare conductors. Population growth in settlements makes it necessary to transmit and distribute electric energy from underground. Insulation is the most important factor in ensuring that electrical energy transmission and distribution with underground cables safely. The insulation problems that may occur in the production of underground cables cause rapidly aging and failures due to partial discharges. In this study, the effect of defects that may occur in the insulation of XLPE insulated cables to electric field distributions in the cable is investigated. In the XLPE insulated cables with 20.3/35 kV, 240 mm 2 and 400 mm 2 conductor cross-sections; electrical field distributions have been investigated by considering problems such as air bubble, water droplets and fiber-like solid particles. Cases of these defects on the surface of the conductor, in the insulator and on the surface of the insulator were considered. The Finite Element Method Magnetics (FEMM) program was used in the analyses.

18 December 2024 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Cihat Cagdas UydurCihat Cagdas Uydur
Cihat Cagdas Uydur
Insulating materials can be classified into solid, liquid, and gaseous forms. Solid insulation materials are divided into different types such as organic, inorganic, and polymer types. In electrical circuits, solid insulation materials are generally used as components that provide insulation and mechanical support. In recent years, as a result of developing technologies, the production of participation insulation materials with 3D printing technology has become widespread. Three-dimensional printing technology enables the rapid creation of objects by combining materials based on digital model data. It is important to evaluate the materials produced with 3D printing in terms of insulation coordination. Studies have shown that the electrical breakdown strength of solid dielectrics varies depending on factors such as sample type, thickness, the magnitude of applied voltage, and the temperature of the physical environment. According to IEC-60243 standards, there are various methods to measure the breakdown strength of solid insulators applied to different voltage types. In this study, the behavior of PLA, ABS, ASA, PETG, and PC/ABS materials produced with 3D printing and having the potential to be used as insulation materials when exposed to high voltage within the scope of insulation coordination was investigated. The breakdown strengths of solid insulation materials produced with 3D printing were measured in the high-voltage laboratory within the scope of IEC-60243. Breakdown strength was statistically evaluated with the Weibull distribution. Damage analysis of the breakdowns in the test specimens was examined in detail with ImageJ software. With the comparative analysis, the behaviors of PLA, ABS, ASA, PETG, and PC/ABS solid insulation materials were revealed and their superiority over each other was determined.