The Lower Silesian Coal Basin in south-western Poland was a region of intensive coal mining until the late 1990s. After mining was stopped and the mines were closed, the underground workings were flooded. This created an underground reservoir of waters that can be economically managed to supply energy, using heat pumps, to the town of Nowa Ruda. The article analyses the energy potential of these waters. It was shown that open loop with reinjection system based on mine shafts can provide 10 GWh of geothermal energy while reducing emissions from 4.27 tCO to 0.22 tCO. In addition, 2.09 GWh can be extracted from water flowing out of mine shafts via adits. As a final result, this will lead to improve air quality as well as increase the environmental value of the region. These results can act as a reference tool for local government, specialists in energy policy at the local scale. They are also the basis for future work aimed at acquiring external funds to carry out detailed studies of the condition of mine shafts, geothermal profiling of water in sunken shafts and test pumping, which will make it possible to determine the real quantities of water to be used.
Predictive maintenance is increasingly popular in many branches, as well as in the mining industry; however, there is a lack of spectacular examples of its practice efficiency. Close collaboration between Omya Group and Wroclaw University of Science and Technology allowed investigation of the failure of the inertial vibrator’s bearing. The signals of vibration are captured from the sieving screen just before bearing failure and right after repair, when it was visually inspected after replacement. The additional complication was introduced by the loss of stable attachment of the vibrator’s shield, which produced great periodical excitation in each place of measurement on the machine. Such anomalies in the signals, in addition to falling pieces of material, made impossible the diagnostics by standard methods. However, the implementation of advanced signal processing techniques such as time–frequency diagrams, envelope spectrum, cyclic spectral coherence, orbits analysis, and phase space plots allowed to undermine defects (pitting on the inner ring). After repair, the amplitudes of vibration from the damaged bearing side were reduced by five times, while sound pressure was only two times lower. The quantitative parameters of vibrations showed significant changes: time series RMS (−68%) median energy of spectrograms (89%), frequencies ratio of cyclic spectral coherence (−85%), and average amplitude of harmonics in envelope spectrum (−80%). The orbits demonstrated changes in inclination angle (16%) and sizes (−48, … −96%), as well as phase space plots sizes (−28, … −67%). Directions of further research are considered.
Mineral segmentation is an equally important and difficult task in the quantification of mineral composition. Difficulties come from the process of determining boundaries of distinctive mineral grains necessary for further analysis and mineral identification. Done by hand, the task is very time-consuming and higher accuracies are burdened with the possible human fatigue factor. The presented method is a fully automated solution to the problem that uses a superpixel approach and feature-based merging. The method is validated by comparison with the manual approach. Analyzed data consist of photos taken by a Nikon Eclipse LV100N POL polarizing microscope at 200× magnification, in transmitted light, with crossed polarizers. Images are first prepared by Gaussian filter and meanshift operations, then the initial segmentation is provided by the superpixel algorithm. Oversegmentation is resolved by feature-based merging. The last step consists of counting the individual grain boundaries and preparing the results as easily readable visual data.
The flooding of unprofitable underground mines is one of the methods of their closure. After the drainage of the mine has stopped, the voids left in the rock mass as a result of mining, are filled with inflowing groundwater. In this way, reservoirs of groundwater with specific physicochemical parameters are formed. These parameters depend on the interaction of the water flowing into the workings with the rock formations. It was the economic situation in the 1990s that led to the closure of hard coal mines in the Nowa Ruda Coal Basin, where the flooded “Nowy I” shaft is located. In that shaft, in 2008, hydrogeological research was performed and groundwater samples from five various depths were collected. The aim of the study was to recognize if groundwater stratification occurs in the shaft. In 2015, a sample of the water outflowing through the “Aleksander” adit was taken to check the potential influence of mine flooding on the environment and to confirm the changes in groundwater chemistry over time. These were the first, and so far, the only studies on the chemical composition of water in the flooded mine in that area. The article presents results of the preliminary research, which confirmed the existence of not obvious hydrogeochemical stratification in the shaft. It can be assumed that below the depth of 350 m, the water circulating through mining excavations exhibits the highest electrical conductivity and the highest concentration of Ca, K, SO, Fe. In the depth range of 320–380 m there is a transition zone, in which a decrease of Eh value and a change of reduction and oxidation is recorded. Above this zone, infiltration water inflow, from outside the shaft casing, dominates. The research shows that it would be necessary to perform additional sampling of the water in the shaft at greater depths, as well as to perform isotope analysis and periodical tests for at least several years. This would allow for a more complete characterisation of hydrogeochemical processes taking place in the flooded mine.
The porosity of rocks is an important parameter used in rock mechanics and underground mining. It affects the movement of fluids in the rock mass and the internal processes taking place (the ability to store water or gases), allowing us to characterize the type of rock and determine possible future applications. Conventional porosity testing methods (e.g., test drill cores in the laboratory) are complex and time-consuming. On the other hand, more modern technologies, such as computed tomography, are high-cost. In the presented study, a core sample with karst and porous structures inside was used. This core sample was poured with resin to reinforce the outer surfaces of the core and make it easier to cut with a rock saw. It was then cut into 3 mm thickness slices in preparation for the next step—the 3D optical scanning. Measurements were made with the ATOS CORE 500 optical scanner. Data processing was then performed in open-source software using popular and commonly used modeling methods. The 3D model of the core reconstructing the actual shape (with internal voids) and the standard model (without internal voids) were created. Based on these, the total porosity of the core was assessed. The presented solution ensures obtaining results with high accuracy at an adequate computational cost using cheap and easily available tools.