Przemysław Dąbek

Mr. Przemysław Dąbek

Department of Geoengineering, Mining and Geology, Wrocław University of Science and Technology, Wrocław, Dolnośląskie, Poland
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
14 January 2022 in Energies
Verified
Journal Article
Open access
PDF file
PDPrzemysław Dąbek
Przemysław Dąbek
JSJarosław Szrek
Jarosław Szrek
Radosław ZimrozRadosław Zimroz
Radosław Zimroz
JWJacek Wodecki
Jacek Wodecki
Complex mechanical systems used in the mining industry for efficient raw materials extraction require proper maintenance. Especially in a deep underground mine, the regular inspection of machines operating in extremely harsh conditions is challenging, thus, monitoring systems and autonomous inspection robots are becoming more and more popular. In the paper, it is proposed to use a mobile unmanned ground vehicle (UGV) platform equipped with various data acquisition systems for supporting inspection procedures. Although maintenance staff with appropriate experience are able to identify problems almost immediately, due to mentioned harsh conditions such as temperature, humidity, poisonous gas risk, etc., their presence in dangerous areas is limited. Thus, it is recommended to use inspection robots collecting data and appropriate algorithms for their processing. In this paper, the authors propose red-green-blue (RGB) and infrared (IR) image fusion to detect overheated idlers. An original procedure for image processing is proposed, that exploits some characteristic features of conveyors to pre-process the RGB image to minimize non-informative components in the pictures collected by the robot. Then, the authors use this result for IR image processing to improve SNR and finally detect hot spots in IR image. The experiments have been performed on real conveyors operating in industrial conditions.

9 September 2022 in Measurement
Verified
Journal Article
Open access
PDPrzemysław Dąbek
Przemysław Dąbek
Pavlo KrotPavlo Krot
Pavlo Krot
JWJacek Wodecki
Jacek Wodecki
PZPaweł Zimroz
Paweł Zimroz
JSJarosław Szrek
Jarosław Szrek
RZRadosław Zimroz
Radosław Zimroz

6 February 2023 in Applied Sciences
Verified
Journal Article
Open access
PDF file
PDPrzemysław Dąbek
Przemysław Dąbek
AWAdam Wróblewski
Adam Wróblewski
JWJacek Wodecki
Jacek Wodecki
PBPiotr Bortnowski
Piotr Bortnowski
MOMaksymilian Ozdoba
Maksymilian Ozdoba
Radosław ZimrozRadosław Zimroz
Radosław Zimroz
Belt mistracking is one of the most dangerous and costly failures of belt conveyors. This phenomenon can lead to complete damage to the conveyor belt, increased demand for electricity from the drive, accelerated wear of route elements, and poses a fire hazard. The article presents the most important causes and ways to detect belt mistracking. Based on the tests carried out at the laboratory test rig, the mechanical and operating parameters of the electric drive of conveyor operation burdened with the problem of lateral running off for the tested belt were compared. The mistracking causes a sudden, differentiated increase in the resistance to movement of the machine, which directly affects the recorded values of forces in the drive system and tensioning mechanism and increases the electrical energy consumption of the drive motor. Belt run monioring based on these parameters is not precise, because there are many other factors on the conveyor route, potentially responsible for the increase in recorded currents and forces. The paper presents an analysis of the possibility of using three, non-contact methods directly monitoring the lateral run-off of the belt, based on vibration measurements of conveyor pulley bearing, RGB images, thermal imaging and measuring the compressive force on the tensioning device.

24 August 2023 in Materials
Verified
Journal Article
Open access
PDF file
Pavlo KrotPavlo Krot
Pavlo Krot
Hamid ShiriHamid Shiri
Hamid Shiri
PDPrzemysław Dąbek
Przemysław Dąbek
Radosław ZimrozRadosław Zimroz
Radosław Zimroz
The condition-based maintenance of vibrating screens requires new methods of their elements’ diagnostics due to severe disturbances in measured signals from vibrators and falling pieces of material. The bolted joints of the sieving deck, when failed, require a lot of time and workforce for repair. In this research, the authors proposed the model-based diagnostic method based on modal analysis of the 2-DOF system, which accounts for the interaction of the screen body and the upper deck under conditions of bolted joint degradation. It is shown that the second natural mode with an out-of-phase motion of the upper deck against the main screen housing may coincide with the excitation frequency or its higher harmonics, which appear when vibrators’ bearings are in bad condition. This interaction speeds up bolt loosening and joint opening by the dynamical loading of higher amplitude. The proposed approach can be used to detune the system from resonance and anti-resonance to reduce maintenance costs and energy consumption. To prevent abrupt failures, such parameters as second natural mode frequency, damping factor, and phase space plot (PSP) distortion measures are proposed as bolt health indicators, and these are verified on the laboratory vibrating screen. Also, the robustness is tested by the impulsive non-Gaussian noise addition to the measurement data. A special diagram was proposed for the bolted joints’ strength capacity assessment and maintenance actions planning (tightening, replacement), depending on clearance in the joints.

9 November 2024 in ISPRS Journal of Photogrammetry and Remote Sensing
Verified
Journal Article
Closed access
PDPrzemysław Dąbek
Przemysław Dąbek
JWJacek Wodecki
Jacek Wodecki
PKPaulina Kujawa
Paulina Kujawa
AWAdam Wróblewski
Adam Wróblewski
AMArkadiusz Macek
Arkadiusz Macek
RZRadosław Zimroz
Radosław Zimroz

2 February 2023 in Minerals
Verified
Journal Article
Open access
PDF file
PDPrzemysław Dąbek
Przemysław Dąbek
KCKrzysztof Chudy
Krzysztof Chudy
INIzabella Nowak
Izabella Nowak
Radosław ZimrozRadosław Zimroz
Radosław Zimroz
Mineral segmentation is an equally important and difficult task in the quantification of mineral composition. Difficulties come from the process of determining boundaries of distinctive mineral grains necessary for further analysis and mineral identification. Done by hand, the task is very time-consuming and higher accuracies are burdened with the possible human fatigue factor. The presented method is a fully automated solution to the problem that uses a superpixel approach and feature-based merging. The method is validated by comparison with the manual approach. Analyzed data consist of photos taken by a Nikon Eclipse LV100N POL polarizing microscope at 200× magnification, in transmitted light, with crossed polarizers. Images are first prepared by Gaussian filter and meanshift operations, then the initial segmentation is provided by the superpixel algorithm. Oversegmentation is resolved by feature-based merging. The last step consists of counting the individual grain boundaries and preparing the results as easily readable visual data.