Dae-Yong Um

Prof. Dae-Yong Um

Department of Electrical Engineering, Gyeongsang National University, Chinju, Gyeongnam, Republic of Korea
orcid

Research Focus & Metrics

Academic Career Length

10Years (2017-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 November 2017 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
HLHa Jeong Lee
Ha Jeong Lee
SISang Hyeon Im
Sang Hyeon Im
DUDae-Yong Um
Dae-Yong Um
GPGwan Soo Park
Gwan Soo Park
There were many attempts to design the rotor bar shape to increase the starting torque in squirrel cage induction motor, and it is well known that deep slot of rotor bar increases the starting torque. However, this deep slot increases the leakage flux so that it hurts the running efficiencies. To increase the running efficiency, it is necessary to keep shallow slot of rotor bar. This paper presents a new design of rotor bar to improve the starting torque without decreasing motor efficiency. The influence of current density of rotor bar on starting torque and rotor copper loss is analyzed so as to design the shapes of rotor bar. In the design, the starting torque was improved by increasing the rotor resistance at startup, and the rotor reactance was maintained during operation. The result showed the improvement of the starting torque without reducing the running efficiency.

18 December 2019 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
DUDae-Yong Um
Dae-Yong Um
GPGwan Soo Park
Gwan Soo Park
Unlike three-phase induction motors, circular rotating fields cannot be inherently formed in single-phase induction motors (SPIMs). Backward rotating fields inevitably result in elliptical rotating fields and degradations of the performance (efficiency, torque). Therefore, the necessity for making rotating fields circular should be emphasized to maximize the effectiveness of design at an arbitrary operating point. In this article, the determination scheme of stator parameters based on circular rotating fields is introduced from equivalent circuits. The derived parameters of stator winding consider circular rotating fields and minimizing copper loss of stator windings, respectively. Then, examples of the design demonstrate the validation of the algorithm. Finally, the comparisons between reference and designed model illustrate that the proposed algorithm can provide insight into the design of high-performance capacitor-run SPIMs.

30 January 2023 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
DUDae-Yong Um
Dae-Yong Um
GPGwan Soo Park
Gwan Soo Park
The DC-magnetization based eddy current testing (ECT) has been developed, and probe signals according to defect orientations are investigated. A focusing field probe was highlighted to improve the sensitivity and compared with that of a circular pancake probe. The limit of the focusing field probe is a reduced sensitivity for parallel oriented defects with lateral misalignment due to its narrow detection area, so this problem hinders the probe detecting arbitrary oriented defects. Therefore, in this paper, we have conducted simulation studies to investigate the effect of DC-magnetization on signals of the probe with the different defect orientations. The results show that superimposing DC-magnetization can widen the detection area of the probe on the application to ferromagnetic steel.

29 June 2020 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
DUDae-Yong Um
Dae-Yong Um
GPGwan Soo Park
Gwan Soo Park
In the high frequency alternating current (AC) fields, both skin effect and proximity effect account for the significant part of losses in an inductor. In particular, serious losses between multiple wires occur due to proximity effect. A stranded wire has two or more strands with twisted structure so that the analysis of stranded wire-wound inductors requires lots of computational time for detailed discretization in finite element analysis (FEA). The analytical method can be alternatively used to help achieve fast (real-time) estimation by reducing the complexity of the original model. However, the proximity effect cannot be accurately predicted due to induced fields by eddy current from adjacent conductors (strands and wires). In this paper, induced fields among adjacent conductors are discussed for the accurate analytical calculation. The concepts of a complex permeability and homogenization can help improve the estimation of frequency-dependent resistance in an inductor. The proposed estimation is verified and compared with the computed value by FEA and measurement data with a spiral inductor.

5 March 2024 in IEEE Access
Verified
Journal Article
Open access
DUDae-Yong Um
Dae-Yong Um
MKMin Jae Kim
Min Jae Kim
SCSeung Ahn Chae
Seung Ahn Chae
GPGwan Soo Park
Gwan Soo Park
Optimizing temperature distribution is one of the crucial tasks in induction heating technology, especially, for small devices with constraints on compactness, efficiency, and cost. The traditional coil shape optimization cannot provide a satisfactory solution with highly limited structural constraints of lateral or vertical size. A multi-coil system where each set of coils is fed by multiple inverters enables control of the magnitude and phase of exciting currents so it can be an alternative approach to enhance the design flexibility. However, additional inverters increase both the volume of a driving circuit and the cost of products, so this approach has a risk of reducing applicability to personal electronics. This article proposed a dual coil system, consisting of primary and secondary coils, to enhance the flexibility for temperature distribution optimization. The impact of primary and secondary coil currents on heat source distribution and efficiency are analyzed, and an equivalent circuit model representing both coils and a workpiece is introduced to provide the main concept of the proposed dual coil system. Resonance characteristics of the dual coil system are studied for a sensitivity analysis of design parameters Finally, the optimization flow is proposed and applied to a case study model to demonstrate its superiority compared to the traditional coil design. Potential challenges are discussed to provide insights for further model development.

13 April 2022 in IEEE Transactions on Magnetics
Verified
Journal Article
Closed access
DUDae-Yong Um
Dae-Yong Um
MKMin Jae Kim
Min Jae Kim
GPGwan Soo Park
Gwan Soo Park
An advanced eddy current (EC) sensor incorporating with direct current (dc) magnetizing unit is presented, and its sensor signals are evaluated numerically considering hysteresis behavior. In this article, we propose an efficient method to calculate sensor signals while considering both a moving magnetizer and a high-frequency alternating current (ac) excitation. The calculation process is divided into two sequential analyses. The first step is a time-domain simulation to calculate a gradual change of dc magnetic field from the moving magnetizer. Then, its solution of the magnetic flux density is stored and used to make a subsequent magnetization curve based on the fitting equation-based hysteresis model. The obtained sub-magnetization curve is used for a time-harmonic simulation, and the sensor signal can be finally obtained. We applied the calculation method to a prototype sensor, and it enables to evaluate sensor signals quantitatively at the different magnetizing field and defect size.