Force detection is an important indicator of a robot's interaction with the working environment. Therefore, accurate and sensitive torque sensor design and development are important. This study proposed a robot joint torque sensor design and optimization based on a strain gauge and through-hole spoke structure topology to detect the external force with high sensitivity and low noise. A through-hole spoke type with a novel inclination sensing surface (ISS) was proposed, and the optimization design improved the strain gauge placement position and focused stress arrangement. Three optimization objectives were desired to enhance the joint torque sensor sensitivity with guaranteed stiffness. A sensor signal processing circuit was also introduced to obtain low-noise output signal performance. The experimental results showed that the joint torque sensor had a high sensitivity of 1.65 mV/Nm before amplification. This sensor was compared with a previous study and a commercial torque sensor. The prototype torque sensor indicated high sensitivity and low error.
3 June 2025 in IEEE/ASME Transactions on Mechatronics
This article introduces a self-balancing bicycle utilizing a reaction wheel for stability control. To manage hardware complexity, a simplified test platform was first used for physical modeling and controller design with a linear-quadratic regulator (LQR), validating the concept. For the final implementation, the full-scale bicycle adopts full-state feedback. Although the LQR improved stability, its frequent motor speed adjustments led to high power consumption. To address this, a novel adaptive equilibrium point gradual algorithm (AEPGA) was developed to adapt to environmental changes, such as lateral imbalances. Performance tests on a real bicycle showed the AEPGA achieved maximum speed of 17 km/h on campus roads. In tests with a 2 kg lateral payload, AEPGA achieved a 67.456% reduction in power consumption compared to LQR over 22 s. For path tracking, a 3D LiDAR system was integrated. On a 77 m indoor corridor, the system reached an average speed of 1.39 km/h with a 0.153 m mean absolute error, while on a 190 m outdoor asphalt road, it reached 2.31 km/h with 0.283 m MAE. These results demonstrate the effectiveness of AEPGA in enhancing energy efficiency and adaptability, while maintaining reliable path tracking in varied environments.
Accurate segmentation of drivable areas and road obstacles is critical for autonomous mobile robots to navigate safely in indoor and outdoor environments. With the fast advancement of deep learning, mobile robots may now perform autonomous navigation based on what they learned in the learning phase. On the other hand, existing techniques often have low performance when confronted with complex situations since unfamiliar objects are not included in the training dataset. Additionally, the use of a large amount of labeled data is generally essential for training deep neural networks to achieve good performance, which is time-consuming and labor-intensive. Thus, this paper presents a solution to these issues by proposing a self-supervised learning method for the drivable areas and road anomaly segmentation. First, we propose the Automatic Generating Segmentation Label (AGSL) framework, which is an efficient system automatically generating segmentation labels for drivable areas and road anomalies by finding dissimilarities between the input and resynthesized image and localizing obstacles in the disparity map. Then, we train RGB-D datasets with a semantic segmentation network using self-generated ground truth labels derived from our method (AGSL labels) to get the pre-trained model. The results showed that our AGSL achieved high performance in labeling evaluation, and the pre-trained model also obtains certain confidence in real-time segmentation application on mobile robots.
This paper presents the design and implementation of a flexible manipulator formed of connected continuum kinematic modules (CKMs) to ease the fabrication of a continuum robot with multiple degrees of freedom. The CKM consists of five sequentially arranged circular plates, four universal joints intermediately connecting five circular plates, three individual actuated tension cables, and compression springs surrounding the tension cables. The base and movable circular plates are used to connect the robot platform or the neighboring CKM. All tension cables are controlled via linear actuators at a distal site. To demonstrate the function and feasibility of the proposed CKM, the kinematics of the continuum manipulator were verified through a kinematic simulation at different end velocities. The correctness of the manipulator posture was confirmed through the kinematic simulation. Then, a continuum robot formed with three CKMs is fabricated to perform Jacobian-based image servo tracking tasks. For the eye-to-hand (ETH) experiment, a heart shape trajectory was tracked to verify the precision of the kinematics, which achieved an endpoint error of 4.03 in Root Mean Square Error (RMSE). For the eye-in-hand (EIH) plugging-in/unplugging experiment, the accuracy of the image servo tracking system was demonstrated in extensive tolerance conditions, with processing times as low as s and s at the 90% confidence level in unplugging and plugging-in tasks, respectively. Finally, quantitative tracking error analyses are provided to evaluate the overall performance.
This paper presents the development, fabrication, and validation of a flexible tactile sensor designed for integration into a hand prosthesis. The proposed sensor design encompasses two distinct prototypes: a fingertip tactile sensor and a palm tactile sensor. Employing a dual-layer structure composed of liquid metal and elastic fibers, these sensors exhibit enhanced sensing capabilities in multiple axes while retaining the capability to deform. The fabrication process includes mold preparation and silicon formulation, body sensor fabrication, Galinstan injection, wire assembly, and creation of a shaped cover for enclosing the tactile palm sensor. A dedicated signal processing circuit is implemented to accommodate the typically small-magnitude and noisy output signals that are characteristic of resistor-based sensors. To enable this signal processing, a filter and programmable gain amplifier-ADC are used for signal conditioning. Finally, experimental data is collected through a computer-microcontroller communication link and displayed through a user interface (UI). The results of the sensor validation experiment demonstrate that the finger tactile sensor can provide 1.557 mV/N, 0.944 mV/N and 1.412 mV/N of the Fx , Fy and Fz , respectively with low-drifting error (0.0265 mV, 0.0145mV and 0.0198 mV) and multi-axis sensing capacity, aligning effectively with the operational requisites of a hand prosthetic robot.
8 January 2025 in International Journal of Fuzzy Systems