Mauricio Gago

Dr. Mauricio Gago

IFN-1, Forschungszentrum Jülich, Jülich, North Rhine-Westphalia, Germany
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2020 in Physica Scripta
Verified
Journal Article
Closed access
Mauricio GagoMauricio Gago
Mauricio Gago
AKA Kreter
A Kreter
BUB Unterberg
B Unterberg
MWMarius Wirtz
Marius Wirtz

3 November 2021 in Physica Scripta
Verified
Journal Article
Closed access
Mauricio GagoMauricio Gago
Mauricio Gago
AKA Kreter
A Kreter
BUB Unterberg
B Unterberg
MWMarius Wirtz
Marius Wirtz
Once ITER commences full power operation, the ITER divertor will be exposed to high thermal and particle loads. Tungsten was chosen as plasma facing material for the ITER divertor. It is, therefore, of the utmost importance to understand the behavior of ITER-grade tungsten under conditions similar to those it will have to withstand inside the reactor. In this study, ITER-grade tungsten samples were exposed to stationary D/He(6%) plasma and ELM-like transient heat loads in the linear plasma device PSI-2. The effects of each kind of load was first studied separately, and the synergistic effects obtained when exposed to both loads simultaneously were then analyzed. Additionally, the hardness of a recrystallized tungsten sample after exposure to simultaneous loads was tested via nanoindentation. The results indicate that hydrogen and helium embrittlement worsens the cracking behavior of the material when exposed to the simultaneous loads compared to only heat loads. Additionally, bubbles of up to 1 μ m are formed under the surface due to the synergistic effects at the highest heat load. The nanoindentation tests showed that plasma and heat loads increase the hardness of the material by 39%, but only plasma loads appeared to have no effect on it.

21 February 2023 in Journal of Nuclear Engineering
Verified
Journal Article
Open access
PDF file
Mauricio GagoMauricio Gago
Mauricio Gago
AKArkadi Kreter
Arkadi Kreter
BUBernhard Unterberg
Bernhard Unterberg
MWMarius Wirtz
Marius Wirtz
Plasma-facing materials (PFMs) in the ITER divertor will be exposed to severe conditions, including exposure to transient heat loads from edge-localized modes (ELMs) and to plasma particles and neutrons. Tungsten is the material chosen as PFM for the ITER divertor. In previous tests, bubble formation in ITER-grade tungsten was detected when exposed to fusion relevant conditions. For this study, ITER-grade tungsten was exposed to simultaneous ELM-like transient heat loads and D/He (6%) plasma in the linear plasma device PSI-2. Bubble formation was then investigated via SEM micrographs and FIB cuts. It was found that for exposure to 100.000 laser pulses of 0.6 GWm−2 absorbed power density (Pabs), only small bubbles in the nanometer range were formed close to the surface. After increasing Pabs to 0.8 and 1.0 GWm−2, the size of the bubbles went up to about 1 µm in size and were deeper below the surface. Increasing the plasma fluence had an even larger effect, more than doubling bubble density and increasing bubble size to up to 2 µm in diameter. When using deuterium-only plasma, the samples showed no bubble formation and reduced cracking, showing such bubble formation is caused by exposure to helium plasma.

Verified
Journal Article
Open access
PDF file
Mauricio GagoMauricio Gago
Mauricio Gago
SASteffen Antusch
Steffen Antusch
AKAlexander Klein
Alexander Klein
AKArkadi Kreter
Arkadi Kreter
Christian LinsmeierChristian Linsmeier
Christian Linsmeier
MWMarius Wirtz
Marius Wirtz
Powder injection molding (PIM) has been used to produce nearly net-shaped samples of tungsten-based alloys. These alloys have been previously shown to have favorable characteristics when compared with standard ITER-grade tungsten. Six different alloys were produced with this method: W-1TiC, W-2Y2O3, W-3Re-1TiC, W-3Re-2Y2O3, W-1HfC and W-1La2O3-1TiC. These were tested alongside ITER-grade tungsten in the PSI-2 linear plasma device under ITER-relevant plasma and heat loads to assess their suitability for use in a fusion reactor. All materials showed good behavior when exposed to the lower pulse number tests (≤1000 ELM-like pulses), although standard tungsten performed slightly better, with no observable difference in surface roughness. High-power shots, namely one laser pulse of 1.6 GWm−2, revealed that samples containing yttria are more prone to melting and droplet ejection. After high pulse number tests (10,000 and 100,000 pulses), with and without plasma, the reference tungsten showed the most cracking and highest surface roughness of all materials, while the PIM samples seemed to have a higher resistance to cracking. This can be attributed to the higher ductility of these alloys, particularly those containing rhenium. This means that tungsten-based alloys, whether produced via PIM or other methods, could potentially be used in certain areas of a fusion reactor.

1 April 2026 in Plasma
Verified
Journal Article
Open access
PDF file
VKVladislav Kotov
Vladislav Kotov
MSMarc Sackers
Marc Sackers
Oleksandr MarchukOleksandr Marchuk
Oleksandr Marchuk
MRMichael Reinhart
Michael Reinhart
GSGennady Sergienko
Gennady Sergienko
SBSebastijan Brezinsek
Sebastijan Brezinsek
Spatially resolved absolute intensities of the atomic lines Hα, Hβ, Hγ, and Hδ have been measured and analyzed in pure hydrogen plasma in the linear plasma device PSI-2. Two regimes have been investigated, with nominal (0.04 Pa) and elevated (0.5 Pa) gas pressure in the sample chamber. The measurements have been compared with local 0D calculations taking into account radiation from H(n=1), H2, and H2+ channels. A baseline plasma chemical mechanism developed in magnetic fusion research was applied to calculate the H2+ density. Both the plasma chemical mechanism and the population factors applied are based on Sawada–Fujimoto collision-radiative model of atomic and molecular hydrogen. The calculations were found to reproduce both the absolute radiation and the line radiation intensity ratios measured in the 0.04 Pa experiment with electron temperature Te = 2–10 eV and electron density ∼5 × 1017 m−3. An exception is the Hα/Hγ intensity ratio, which tends to be overestimated by the model. The calculations suggest that the majority of the observed Balmer radiation in this regime is due to the H2+ channel. At the same time, both the applied simplified approach without detailed transport modeling and the baseline mechanism were found to be inappropriate for the 0.5 Pa experiment with reduced Te = 1–5 eV. This experimental regime can serve as a benchmark of more sophisticated hydrogen plasma models.

7 September 2025 in Nuclear Materials and Energy
Verified
Journal Article
Open access
JTJannik Tweer
Jannik Tweer
TDThomas Derra
Thomas Derra
DDDaniel Dorow-Gerspach
Daniel Dorow-Gerspach
Mauricio GagoMauricio Gago
Mauricio Gago
SGSascha Gierlings
Sascha Gierlings
GNGhaleb Natour
Ghaleb Natour