Alperen Degirmenci

Dr. Alperen Degirmenci

University of Van Yuzuncu Yil, Van, Turkey (Türkiye)
orcid

Research Focus & Metrics

Academic Career Length

9Years (2018-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
15 June 2026 in Odovtos - International Journal of Dental Sciences
Verified
Journal Article
Open access
PDF file
ADAlperen Degirmenci
Alperen Degirmenci
DCDilber Bilgili Can
Dilber Bilgili Can
The aim of this study was to investigate the effect of preheating three bulk-fill and one conventional composite resin on the Vickers microhardness and depth of cure of these composites. In this study, three bulk-fill composites-SDR Plus (SDR), Estelite BULK FILL Flow (EST), Admira® Fusion x-tra (AFX), and one conventional composite resin G-ænial POSTERIOR (GP) were used as the control group. The samples were obtained at room temperature (24°C) and at 55°C in T2 mode after being placed in a heating device for 10 minutes. The samples were divided into eight groups (n=10) according to the type of material and heating process that was utilized (preheated and nonheated). All samples were tested with a Vickers microhardness (VHN) tester on the bottom and top surfaces. The first measurements were obtained at baseline; the second set of measurements was performed after the samples were stored in distilled water at 37°C for 24 hours. The depth of cure was calculated using a bottom/top hardness ratio of measurements. Statistical analysis was performed utilizing the SPSS V23 and Shapiro-Wilk tests. Lastly, the Duncan test was used for multiple comparisons (p<0.05). While the VHN increased after the preheating procedure in bulk-fill composites, it decreased in GP. There was no difference between the baseline and the 24-hour VHN values in SDR and GP. After 24 hours, while the VHN of EST increased, the VHN of AFX decreased. There was no difference between the hardness ratios of the AFX and EST samples (p<0.001) and hardness ratios were greater than GP and SDR. When comparing the baseline and the 24-hour values, the VHN depended on the type of materials. Sufficient curing depth was obtained in all groups with a thickness of 2mm.

1 August 2018 in American Journal of Orthodontics and Dentofacial Orthopedics
Verified
Journal Article
Closed access
YKYeşim KAYA
Yeşim KAYA
ÖAÖzer Alkan
Özer Alkan
ADAlperen Degirmenci
Alperen Degirmenci
SKSıddık Keskin
Sıddık Keskin


Verified
Journal Article
Open access
PDF file
BDBeyza Ünalan Değirmenci
Beyza Ünalan Değirmenci
ADAlperen Degirmenci
Alperen Degirmenci
ZPzelal seyfioglu polat
zelal seyfioglu polat
Background: The durability of computer-aided design/computer-aided manufacturing (CAD/CAM) resin nanoceramics in the oral environment is influenced by aging factors such as thermocycling and ultraviolet (UV) exposure. This study investigates the impact of these aging processes on surface characteristics and repair bond strength. Methods: CAD/CAM resin nanoceramic samples were divided into the following five groups: control (non-aged), 1-year and 5-year thermocycling, and 1-year and 5-year UV aging (n = 12). For the thermocycling procedure, the parameters employed were a temperature range of 5–55 °C with dwell times of 20 s per bath and 10,000 and 50,000 cycles; for the ultraviolet aging process, the parameters were established at a wavelength of 340 nm, an intensity of 0.55 W/m², and durations of 300 h and 1500 h. Surface roughness, microhardness, and repair bond strength were analyzed through profilometry, Vickers microhardness testing, and shear bond strength assessment, respectively. SEM, AFM, and XRD analyses were performed for structural evaluation. Results: Both thermocycling and UV aging significantly increased surface roughness (p < 0.001) while reducing microhardness and repair bond strength (p < 0.001). UV aging had a more pronounced effect, particularly after five years, leading to the highest surface roughness (Ra: 61.77 μm; Rz: 271.57 μm) and lowest microhardness properties (63.13). EDAX analysis indicated matrix degradation and an increase in inorganic filler exposure. Conclusions: Aging significantly affects the surface characteristics of CAD/CAM resin nanoceramics, with UV aging exhibiting the most detrimental impact. These findings highlight the necessity of considering long-term material stability in dentistry.

2 August 2024 in Polymers
Verified
Journal Article
Open access
PDF file
ADAlperen Degirmenci
Alperen Degirmenci
BDBeyza Ünalan Değirmenci
Beyza Ünalan Değirmenci
This study aims to evaluate the repair micro-shear bond strength of the CAD/CAM resin nanoceramic block treated using four different surface treatments and composite resins of different viscosities. For the current study, 96 samples with dimensions of 14 × 12 × 2 mm were obtained from a CAD/CAM resin nanoceramic block (Cerasmart) with a low-speed precision cutting saw under water cooling. The relevant samples were randomly divided into four groups according to the surface treatment processes: grinding with diamond bur, aluminum oxide airborne-particle abrasion, long-pulse laser, and short-pulse laser. Following silane application, universal adhesive was applied to all surface-treated samples and cured with an LED for 10 s. The samples prepared for the repair procedure were divided into two subgroups (microhybrid composite and injectable composite) according to the viscosity of the repair material to be used (n = 12). After the repair procedure, care was taken to keep the samples in distilled water in an incubator at 37 °C for 24 h. The repair micro-shear bond strength values (μSBSs) of CAD/CAM resin nanoceramic-composite resin complexes were tested. In addition, randomly selected samples from each group were examined with a scanning electron microscope to evaluate the surface topography after both surface treatments and the micro-shear bond strength test. Data were analyzed by two-way ANOVA and Bonferroni test. It was determined that the surface treatment preferred in the repair protocol significantly affected the μSBS value (p < 0.001). While the highest μSBS value was obtained with the short-pulse laser airradiation group, the lowest μSBS values were found in samples with long pulse laser irradiation. However, samples grinded with a bur and airborne-particle abrasion showed similar μSBS values (p > 0.05). The preferred composite viscosity in the repair procedure has a significant effect on the μSBS value (p < 0.001). However, the interaction between the surface treatment and the viscosity of the repair composite does not affect the μSBS values in a statistically significant way (p = 0.193). It may be recommended to clinicians to repair CAD/CAM resin nanoceramic restoration surfaces with injectable composites or after treatment with short-pulse lasers.

6 December 2021 in International Journal of Applied Ceramic Technology
Verified
Journal Article
Closed access
PDF file
BDBeyza Ünalan Değirmenci
Beyza Ünalan Değirmenci
ADAlperen Degirmenci
Alperen Degirmenci
BNBeyza Karadag Naldemir
Beyza Karadag Naldemir