The Smart Grid is one of the most important solutions to boost electricity sharing from renewable energy sources. Its implementation adds new functionalities to power systems, which increases the electric grid complexity. To ensure grid stability and security, systems need flexible methods in order to be tested in a safe and economical way. A promising test technique is Power Hardware-In-the-Loop (PHIL), which combines the flexibility of Hardware-In-the-Loop (HIL) technique with power exchange. However, the acquisition of PHIL components usually represents a great expense for laboratories and, therefore, the setting up of the experiment involves making hard decisions. This paper provides a complete guideline and useful new tools for laboratories in order to set PHIL facilities up efficiently. First, a PHIL system selection guide is presented, which describes the selection process steps and the main system characteristics needed to perform a PHIL test. Furthermore, a classification proposal containing the desirable information to be obtained from a PHIL test paper for reproducibility purposes is given. Finally, this classification was used to develop a PHIL test online database, which was analysed, and the main gathered information with some use cases and conclusions are shown.
The electric vehicle (EV) is considered as one of the most promising solutions to important problems of the current mobility model: high energy consumption (low efficiency), air pollution and dependence of fossil fuels. Despite its significant benefits, a massive deployment of electric vehicles could create important issues in the electric system, mainly in distribution grids: saturation due to increase of electric demand and power quality deterioration. Moreover, owners of EV charging facilities need to increase contracted power with an extra-cost of operation. In this paper, a show case is presented, how to install a complete EV charging station in an existing petrol station, solving power quality problems and without increasing contracted power.
Nowadays, the global decarbonization and electrification of the world’s energy demands have led to the quick adoption of Electric Vehicle (EV) technology. Therefore, there is an urgent need to provide a wide network of fast Vehicle-to-Grid (V2G) charging stations to support the forecast demand and to enable enough autonomy of such devices. Accordingly, V2G charging stations must be prepared to work properly with every manufacturer and to provide reliable designs and validation processes. In this way, the development of power electric vehicle emulators with V2G capability is critical to enable such development. The paper presents a complete design of a power electric vehicle emulator, as well as an experimental testbench to validate the behaviour of the proposal.
Solid-State Transformers (SSTs) enable significant improvements in size and functionality compared to conventional power transformers. However, one of the key challenges in Solid-State Transformer design is achieving reliable insulation between the high-voltage and low-voltage sections. This proposal presents the design and optimization of a high-insulation Medium-Frequency Transformer (MFT) for 66 kV grids operating at 50 kHz and delivering up to 75 kW for SST applications using Inductive Power Transfer (IPT) technology. A fixed 50 mm gap between the primary and secondary windings is filled with dielectric oil to enhance insulation. The proposed IPT system employs a double-D coil design developed through iterative 2D and 3D finite element method simulations to optimize the magnetic circuit, thereby significantly reducing stray flux and losses. Notably, the double-D configuration reduces enclosure losses from 269.6 W, observed in a rectangular coil design, to 4.38 W, resulting in an overall system loss reduction of 42.4% while maintaining the electrical parameters required for zero-voltage switching operation. These advancements address the critical limitations in conventional Medium-Frequency Transformers by providing enhanced insulation and improved thermal management. The proposed IPT-based design offers a low-loss solution with easy thermal management for solid-state transformer applications in high-voltage grids.
22 May 2012 in WIT Transactions on Ecology and the Environment
The growing emergence of Distributed Energy Resources (DER) that operate natively in DC challenges the traditional logic of unidirectional power flow and the exclusive use of AC in distribution systems due to inefficiency and control problems. DC microgrids are seen as a promising alternative to address these challenges, and Solid-State Transformers (SSTs) could be a feasible solution to enable the development of such controllable hybrid DC/AC grids. This paper presents the design, modular topology, and experimental validation of a 150 kVA SiC-based SST. This SST follows a four-module input-parallel, output-series configuration, enabling the creation of a 3 kV MV DC microgrid from the LV AC electrical grid, allowing intrinsic voltage balancing among modules, straightforward scalability in both voltage and power, and easier maintenance. Each two-stage module, in turn, consists of an active front-end and an isolated DC/DC, which is composed of a dual full-bridge driving a series CLLC resonant tank at 88-90 kHz. Laboratory and field tests demonstrate continuous DC voltage regulation in a range from 1.2 kV to 3 kV, black-start capability and support of the AC grid through reactive power. The prototype achieves a power conversion efficiency of 96.4 % under nominal conditions while transferring 151.6 kW, with line current THD remaining below 1.8 %. The SST, along with the constructed MV DC microgrids, addresses the lack of real demonstrators that can validate the benefits of DC integration.