Egidio D’Amato

Prof. Egidio D’Amato

Department of Science & Technology, Parthenope University of Naples, Naples, Campania, Italy
orcid

Research Focus & Metrics

Academic Career Length

16Years (2011-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 January 2014 in Aerospace Science and Technology
Verified
Journal Article
Closed access
Pierluigi Della VecchiaPierluigi Della Vecchia
Pierluigi Della Vecchia
EDElia Daniele
Elia Daniele
Egidio D’AmatoEgidio D’Amato
Egidio D’Amato

23 December 2019 in Sensors
Verified
Journal Article
Open access
PDF file
Marcello FeraMarcello Fera
Marcello Fera
Alessandro GrecoAlessandro Greco
Alessandro Greco
Mario CaterinoMario Caterino
Mario Caterino
SGSalvatore Gerbino
Salvatore Gerbino
Francesco CaputoFrancesco Caputo
Francesco Caputo
Egidio D’AmatoEgidio D’Amato
Egidio D’Amato
The optimization of production processes has always been one of the cornerstones for manufacturing companies, aimed to increase their productivity, minimizing the related costs. In the Industry 4.0 era, some innovative technologies, perceived as far away until a few years ago, have become reachable by everyone. The massive introduction of these technologies directly in the factories allows interconnecting the resources (machines and humans) and the entire production chain to be kept under control, thanks to the collection and the analyses of real production data, supporting the decision making process. This article aims to propose a methodological framework that, thanks to the use of Industrial Internet of Things—IoT devices, in particular the wearable sensors, and simulation tools, supports the analyses of production line performance parameters, by considering both experimental and numerical data, allowing a continuous monitoring of the line balancing and performance at varying of the production demand. A case study, regarding a manual task of a real manufacturing production line, is presented to demonstrate the applicability and the effectiveness of the proposed procedure.

28 April 2021 in Sensors
Verified
Journal Article
Open access
PDF file
Egidio D’AmatoEgidio D’Amato
Egidio D’Amato
VNVito Antonio Nardi
Vito Antonio Nardi
Immacolata NotaroImmacolata Notaro
Immacolata Notaro
VSValerio SCORDAMAGLIA
Valerio SCORDAMAGLIA
Sensor fault detection and isolation (SFDI) is a fundamental topic in unmanned aerial vehicle (UAV) development, where attitude estimation plays a key role in flight control systems and its accuracy is crucial for UAV reliability. In commercial drones with low maximum take-off weights, typical redundant architectures, based on triplex, can represent a strong limitation in UAV payload capabilities. This paper proposes an FDI algorithm for low-cost multi-rotor drones equipped with duplex sensor architecture. Here, attitude estimation involves two 9-DoF inertial measurement units (IMUs) including 3-axis accelerometers, gyroscopes and magnetometers. The SFDI algorithm is based on a particle filter approach to promptly detect and isolate IMU faulted sensors. The algorithm has been implemented on a low-cost embedded platform based on a Raspberry Pi board. Its effectiveness and robustness were proved through experimental tests involving realistic faults on a real tri-rotor aircraft. A sensitivity analysis was carried out on the main algorithm parameters in order to find a trade-off between performance, computational burden and reliability.

11 June 2018 in IEEE Transactions on Instrumentation and Measurement
Verified
Journal Article
Closed access
Egidio D’AmatoEgidio D’Amato
Egidio D’Amato
Massimiliano MatteiMassimiliano Mattei
Massimiliano Mattei
Immacolata NotaroImmacolata Notaro
Immacolata Notaro
VSValerio Scordamaglia
Valerio Scordamaglia
A fault detection and isolation algorithm for the attitude estimation of an unmanned aerial vehicle (UAV) using low-cost magnetometers, accelerometers, and gyroscopes, implemented in an inertial measurement unit (IMU) is proposed. Assuming the availability of double triaxial gyros, accelerometers, and magnetometers, the possibility that fault can occur both in input (gyros outputs) and in output (accelerometers and magnetometers outputs) to the kinematic nonlinear relations underlying attitude estimation must be taken into account. If an extended Kalman filter (EKF) can compensate for biases on gyroscopes, fault detection, for all sensors, is first obtained with a comparison between homogeneous sensor outputs. Then, the isolation of the faulted gyro is carried out through the analysis of the EKF bias estimates, whereas a set-based approach is used to isolate faulted accelerometers or magnetometers. For these sensors, isolation tests involve the solution of a linear programming problem on a moving time window in the discrete time domain. In order to show the practical applicability and robustness against measurement noise and different kind of faults, a set of simulations involving experimental data collected during flights of a tricopter UAV are discussed.

11 June 2019 in Journal of Intelligent & Robotic Systems
Verified
Journal Article
Closed access
PDF file
Egidio D’AmatoEgidio D’Amato
Egidio D’Amato
Massimiliano MatteiMassimiliano Mattei
Massimiliano Mattei
INImmacolata Notaro
Immacolata Notaro

11 May 2018 in Journal of Intelligent & Robotic Systems
Verified
Journal Article
Closed access
PDF file
Egidio D’AmatoEgidio D’Amato
Egidio D’Amato
Massimiliano MatteiMassimiliano Mattei
Massimiliano Mattei
Immacolata NotaroImmacolata Notaro
Immacolata Notaro