In this research, a low molecular weight poly(lactic acid) (or PLA) synthesized from direct polycondensation was melt compounded with urea to formulate slow-release fertilizer (SRF). We studied the influence of the molecular weight (MW) of PLA as a matrix and the urea composition of SRF towards release kinetics in water at 30 °C. The physical appearance of solid samples, the change in urea concentration, and acidity (pH) of water were monitored periodically during the release test. Three studied empirical models exhibited that diffusion within the matrix dominated the urea release process, especially when the release level was less than 60%. Thus, a lower MW of PLA and a higher urea content of SRF showed a faster release rate. For the entire length of the release experiment, a combination of diffusion and degradation mechanisms exhibited the best agreement with the experimental data. The hydrolytic degradation of PLA may begin after 96 h of immersion (around 60% release level), followed by the appearance of some micro-holes and cracks on the surface of the SRF samples. Generally, this research revealed the good release performance of urea without residues that damage the soil structure and nutrient balance.
Conductive polymer composites (CPCs) have attracted great attention of researchers due to their enhanced properties such as an adjustable electrical conductivity, good processability, good mechanical and thermal properties, etc. CPCs had many potencies for wider application in electronic devices. Poly (lactic acid) or PLA is one of the interesting polymers used in the developing of these new important materials. PLA properties are comparable to the synthetic petroleum-based polymers such as polyethylene terephthalate (PET), polypropylene (PP), etc. This research focuses on studying the rheological and thermal properties of PLA/micro-graphite as a conductive polymer composite which adjustable its electrical conductivity. In this study, the PLA/micro-graphite was prepared through solvent blending method using chloroform. The micro-graphite composition was varied from 0%, 5%, and 10 % (w/w) with different stirring time (30 and 60 minutes) and then, poured in glass mould. In the melt rheology study, the frequency sweep test showed that the complex viscosity (|η*|) of the bio-composite increased with the micro-graphite loading. The same tendency was also found in thermal property and stability. The melting temperature and thermal degradation were slightly increasing. The crystallinity of PLA was influenced by the presence of micro-graphite. In this solvent blending method, the homogeneous distribution of micro-graphite in the bio-composite required at least 60 minutes (stirred at 650 rpm and 60 °C).
Micro-graphite was incorporated into poly(lactic acid) via solution blending in chloroform with varying concentrations: 0, 5, 10, and 15%wt. Before being poured in the glass mold, the adding micro-graphite is accompanied by stirring at 650 rpm and 60o-C (for 1 hour) to homogenize the dispersion of micro-graphite into the PLA solution. This report is discussing the characterization results of the prepared micro-composites, i.e., crystallinity and electrical properties. The crystallinity was analyzed using X-ray Diffraction (XRD) and Differential Scanning Calorimetry (DSC). Both surface and bulk crystallinity were demonstrating a considerable dependence with the micro-graphite loading. The onset temperature of the melting point has a slight shift about 2-4oC. However, the melting point of neat PLA and micro- composites is not significantly changed. The electrical property was carried by Keithley 2602A SYSTEM SourceMeter to measure their resistivity. In the voltage range of 0-1 volt, the presence of micro-graphite starts to have an impact at 15%wt load. Resistivity decreases become 1,686x104 O.mm from out of the device measurement range. The ATR-FTIR (Attenuated Total Reflection-FTIR) spectra show that the residue of chloroform solvent is not detected in the dry prepared samples. It means the solvent can be predicted totally evaporated from the sample.
In fulfilling its pigment material needs for industrial purposes, Indonesia still relies on imports, whose value continues to rise. This shows that the abundance of local raw materials has not been utilized optimally. Iron, as one of the pigment materials, can be obtained from the refining of metal waste. One of the metal wastes with a high Fe content (up to 97.11% w/w) is used in the manufacture of dishwashing wire. The manufacture of pigments from metal waste has the potential for sales value and commercial-scale development. The pigments synthesized are Prussian blue (iron (III) ferrocyanide or Fe 4 [Fe(CN) 6 ] 3 ) and oxide red (iron (III) oxide or Fe 2 O 3 ). Iron recovery is carried out using the leaching method with acids, specifically HCl and H 2 SO 4 . After the iron is dissolved in the acid and the dregs are filtered, the process continues with the oxidation stage, using H 2 O 2 as the oxidizing agent. The precipitation stage is carried out using NaOH and K 3 Fe(CN) 6 . After undergoing filtration and washing, the pigment is heated in an oven until a crystalline powder is obtained. Prussian blue and oxide red pigments were successfully synthesized, with coloring tending towards a Prussian blue hue. This is because the synthesized Prussian blue is more easily dispersed in CMC solution than the oxide red pigment. Several samples were found to change their tendency to oxidize red after sieving >90 mesh, indicating the influence of grain size on pigment mixing. FTIR testing revealed the presence of CN, Fe-O, and Fe-CN functional groups, confirming the presence of these groups in the pigment. This finding was reinforced by EDX testing, which showed the presence of Fe, C, N, and O atoms. From the SEM test of the pigment sieving >90 mesh, irregular angular crystal particles were produced with a size of 0.9-23.6 µm.
Composite synthesis from styrofoam (polystyrene-based) was carried out by solvent blending method in which the solvent used was gasoline. The carbon black (CB) was used as filler comes from coconut shells. The samples were given a variation of filler composition: 0, 1, 3, and 5% of the total weight of the composite to be formed. In this method, stirring was carried out for at least 120 minutes (200 rpm in atmospheric conditions). The stirring process is carried out until the mixture becomes homogeneous, as indicated by the slurry formation. After that, the process continues to the printing stage using glass mold and drying in a windy room that is sufficiently exposed to sunlight for 3 days. The sample obtained is a composite measuring 8 cm x 8 cm. The tests carried out were the ATR-FTIR, SEM, conductivity, and mechanical tests. From the results of the ATR-FTIR test, there was no visible difference between the styrofoam before being treated with the composites, thus proving that the solvent had evaporated. The results of the SEM test show that there are lumps in the sample with higher filler concentrations, so it is possible to need additional time or stirring speed to distributed the filler evenly. Meanwhile, the conductivity test proved that the addition of carbon-based filler could increase the conductivity of the composites.