Fabian Kühnel

Mr. Fabian Kühnel

Deggendorf Institute of Technology, Deggendorf, Bavaria, Germany
orcid

Research Focus & Metrics

Academic Career Length

7Years (2020-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
21 April 2023 in ACS Applied Materials & Interfaces
Verified
Journal Article
Open access
JWJonas Weber
Jonas Weber
YYYue Yuan
Yue Yuan
FKFabian Kühnel
Fabian Kühnel
CMChristoph Metzke
Christoph Metzke
JSJosef Schaetz
Josef Schaetz
MLMario Lanza
Mario Lanza
Conductive atomic force microscopy (CAFM) is a powerful technique to investigate electrical and mechanical properties of materials and devices at the nanoscale. However, its main challenge is the reliability of the probe tips and their interaction with the samples. The most common probe tips used in CAFM studies are made of Si coated with a thin (∼20 nm) film of Pt or Pt-rich alloys (such as Pt/Ir), but this can degrade fast due to high current densities (>102A/cm2) and mechanical frictions. Si tips coated with doped diamond and solid doped diamond tips are more durable, but they are significantly more expensive and their high stiffness often damages the surface of most samples. One growing alternative is to use solid Pt tips, which have an intermediate price and are expected to be more durable than metal-coated silicon tips. However, a thorough characterization of the performance of solid Pt probes for CAFM research has never been reported. In this article, we characterize the performance of solid Pt probes for nanoelectronics research by performing various types of experiments and compare them to Pt/Ir-coated Si probes. Our results indicate that solid Pt probes exhibit a lateral resolution that is very similar to that of Pt/Ir-coated Si probes but with the big advantage of a much longer lifetime. Moreover, the probe-to-probe deviation of the electrical data collected is small. The use of solid Pt probes can help researchers to enhance the reliability of their CAFM experiments.

22 January 2020 in Materials
Verified
Journal Article
Open access
PDF file
CMChristoph Metzke
Christoph Metzke
WFWerner Frammelsberger
Werner Frammelsberger
JWJonas Weber
Jonas Weber
FKFabian Kühnel
Fabian Kühnel
KZKaichen Zhu
Kaichen Zhu
GBGünther Benstetter
Günther Benstetter
Heat transfer processes in micro- and nanoscale devices have become more and more important during the last decades. Scanning thermal microscopy (SThM) is an atomic force microscopy (AFM) based method for analyzing local thermal conductivities of layers with thicknesses in the range of several nm to µm. In this work, we investigate ultrathin films of hexagonal boron nitride (h-BN), copper iodide in zincblende structure (γ-CuI) and some test sample structures fabricated of silicon (Si) and silicon dioxide (SiO2) using SThM. Specifically, we analyze and discuss the influence of the sample topography, the touching angle between probe tip and sample, and the probe tip temperature on the acquired results. In essence, our findings indicate that SThM measurements include artefacts that are not associated with the thermal properties of the film under investigation. We discuss possible ways of influence, as well as the magnitudes involved. Furthermore, we suggest necessary measuring conditions that make qualitative SThM measurements of ultrathin films of h-BN with thicknesses at or below 23 nm possible.

21 November 2023 in ACS Applied Materials & Interfaces
Verified
Journal Article
Closed access
JWJonas Weber
Jonas Weber
YYYue Yuan
Yue Yuan
SPSebastian Pazos
Sebastian Pazos
FKFabian Kühnel
Fabian Kühnel
CMChristoph Metzke
Christoph Metzke
MLMario Lanza
Mario Lanza

16 February 2021 in Nanomaterials
Verified
Journal Article
Open access
PDF file
CMChristoph Metzke
Christoph Metzke
FKFabian Kühnel
Fabian Kühnel
JWJonas Weber
Jonas Weber
GBGünther Benstetter
Günther Benstetter
New micro- and nanoscale devices require electrically isolating materials with specific thermal properties. One option to characterize these thermal properties is the atomic force microscopy (AFM)-based scanning thermal microscopy (SThM) technique. It enables qualitative mapping of local thermal conductivities of ultrathin films. To fully understand and correctly interpret the results of practical SThM measurements, it is essential to have detailed knowledge about the heat transfer process between the probe and the sample. However, little can be found in the literature so far. Therefore, this work focuses on theoretical SThM studies of ultrathin films with anisotropic thermal properties such as hexagonal boron nitride (h-BN) and compares the results with a bulk silicon (Si) sample. Energy fluxes from the probe to the sample between 0.6 µW and 126.8 µW are found for different cases with a tip radius of approximately 300 nm. A present thermal interface resistance (TIR) between bulk Si and ultrathin h-BN on top can fully suppress a further heat penetration. The time until heat propagation within the sample is stationary is found to be below 1 µs, which may justify higher tip velocities in practical SThM investigations of up to 20 µms−1. It is also demonstrated that there is almost no influence of convection and radiation, whereas a possible TIR between probe and sample must be considered.

4 June 2022 in Nanomaterials
Verified
Journal Article
Open access
PDF file
FKFabian Kühnel
Fabian Kühnel
CMChristoph Metzke
Christoph Metzke
JWJonas Weber
Jonas Weber
JSJosef Schaetz
Josef Schaetz
GDGeorg Duesberg
Georg Duesberg
GBGünther Benstetter
Günther Benstetter
A well-known method for measuring thermal conductivity is the 3-Omega (3ω) method. A prerequisite for it is the deposition of a metal heater on top of the sample surface. The known design rules for the heater geometry, however, are not yet sufficient. In this work, heaters with different lengths and widths within the known restrictions were investigated. The measurements were carried out on SiO2 thin films with different film thicknesses as a reference. There was a significant difference between theoretical deposited heater width and real heater width, which could lead to errors of up to 50% for the determined thermal conductivity. Heaters with lengths between 11 and 13 mm and widths of 6.5 µm or more proved to deliver the most trustworthy results. To verify the performance of these newfound heaters, additional investigations on Al2O3 thin films were carried out, proving our conclusions to be correct and delivering thermal conductivity values of 0.81 Wm−1 K−1 and 0.93 Wm−1 K−1 for unannealed and annealed samples, respectively. Furthermore, the effect of annealing on Al2O3 was studied, revealing a significant shrinking in film thickness of approximately 11% and an increase in thermal conductivity of 15%. The presented results on well-defined geometries will help to produce optimized heater structures for the 3ω method.

15 March 2026 in Advanced Materials Interfaces
Verified
Journal Article
Open access
PDF file
JSJosef Schaetz
Josef Schaetz
MKMichael Krenzer
Michael Krenzer
TSTim Schaffus
Tim Schaffus
MOMartin Otto
Martin Otto
FKFabian Kühnel
Fabian Kühnel
MLMax Lemme
Max Lemme
Boron nitride (BN) is considered for several applications in microelectronics, such as thermal management, optoelectronics, or as memristors. BN can be deposited with different deposition methods, but any integration in the back‐end‐of‐the‐line limits the deposition temperature to approximately 400°C. Further requirements include high crystal quality, sufficient film stability, and a high deposition rate to limit process costs. In particular, investigations into thin film stability and high deposition rates have rarely been conducted. Here, we propose reactive pulsed direct current sputtering at 250°C from a pure boron target and demonstrate the deposition process for stable nanocrystalline turbostratic BN. A substrate bias voltage between the plasma and sample reduces excess boron in the film and enhances its crystallinity. The process effectively prevents the formation of boric acid and ammonium borate hydrate. The stable BN films have a crystallite size of approximately 5 nm and an out‐of‐plane texture. Leakage current investigations demonstrate the insulating properties of the films. A high deposition rate of 81.6 nm min – 1 and the use of state‐of‐the‐art sputter hardware allow the immediate integration of sputtered BN into semiconductor device process lines.