Multiple satellite products are available to monitor the spatiotemporal dynamics of surface albedo. They are extensively assessed over snow-free surfaces but less over snow. However, snow albedo is critical for climate monitoring applications, so a better understating of the accuracy of these products over snow is needed. This work analyzes long-term (+20 years) products (MCD43C3 v6/v6.1, GLASS-AVHRR, C3S v1/v2) by comparing them against the 11 most spatially representative stations from FLUXNET and BSRN during the snow-free and snow-covered season. Our goal is to understand how the performance of these products is affected by different snow cover conditions to use this information in an upcoming product inter-comparison that extends the analysis spatially and temporally. MCD43C3 has the smallest bias during the snow season (−0.017), and more importantly, the most stable bias with different snow cover conditions. Both v6 and v6.1 have similar performance, with v6.1 just increasing slightly the coverage at high latitudes. On the contrary, the quality of both GLASS-AVHRR and C3S-v1/v2 albedo decreases over snow. Particularly, the bias of both products varies strongly with the snow cover conditions, underestimating albedo over snow and overestimating snow-free albedo. GLASS bias strongly increases during the melting season, which is most likely due to an artificially extended snow season. C3S-v2 has the largest negative bias overall over snow during both the AVHRR (−0.141) and SPOT/VGT (−0.134) period. In addition, despite the improvements from v1 to v2, C3S-v2 still is not consistent enough during the transition from AVHRR to SPOT/VGT.
The fraction of absorbed photosynthetically active radiation (FAPAR) is one of the bio-geophysical Essential Climate Variables assessed through remote sensing observations and distributed globally by space and environmental agencies. Any reliable remote sensing product should be benchmarked against a reference, which is normally determined by means of ground-based measurements. They should generally be aggregated spatially to be compared with remote sensing products at different resolutions. In this work, the effectiveness of various in situ sampling methods proposed to assess FAPAR from flux measurements was evaluated using a three-dimensional radiative transfer framework over eight virtual vegetated landscapes, including dense forests (leaf-on and leaf-off models), open canopies, sparse vegetation, and agricultural fields with a nominal extension of 1 hectare. The reference FAPAR value was determined by summing the absorbed PAR-equivalent photons by either all canopy components, both branches and leaves, or by only the leaves. The incoming and upwelling PAR fluxes were simulated in different illumination conditions and at a high spatial resolution (50 cm). They served to replicate in situ virtual FAPAR measurements, which were carried out using either stationary sensor networks or transects. The focus was on examining the inherent advantages and drawbacks of in situ measurement protocols against GCOS requirements. Consequently, the proficiency of each sampling technique in reflecting the distribution of incident and reflected PAR fluxes—essential for calculating FAPAR—was assessed. This study aims to support activities related to the validation of remote sensing FAPAR products by assessing the potential uncertainty associated with in situ determination of the reference values. Among the sampling schemes considered in our work, the cross shaped sampling schemes showed a particular efficiency in properly representing the pixel scale FAPAR over most of the scenario considered.
This paper aims to assess the relationship between the surface reflectance derived from ground based and aircraft measurements. The parameters of the Rahman–Pinty–Verstraete (RPV) and Ross Thick-LiSparse (RTLS) kernel based bi-directional reflectance distribution functions (BRDF), have been derived using actual measurements of the hemispherical-directional reflectance factor (HDRF), collected during different campaigns over the Railroad Valley Playa. The effect of the atmosphere, including that of the diffuse radiation on bi-directional reflectance factor (BRF) parameter retrievals, assessed using 6S model simulations, was negligible for the low turbidity conditions of the site under investigation (). It was also shown that the effects of the diffuse radiation on RPV spectral parameters retrieval is linear for the isotropic parameter and the scattering parameter , and can be described with a second order polynomial for the k-Minnaert parameter. In order to overcome the lack of temporal collocations between aircraft and in-situ measurements, Monte Carlo 3-D radiative transfer simulations mimicking in-situ and remote sensing techniques were performed on a synthetic parametric meshed scene defined by merging Landsat and Multianglhe Imaging Spectroradiometer (MISR) remote sensing reflectance data. We simulated directional reflectance measurements made at different heights for PARABOLA and CAR, and analyzed them according to practices adopted for real measurements, consisting of the inversion of BRF functions and the calculation of the bi-hemispherical reflectance (BHR). The difference of retrievals against the known benchmarks of kernel parameters and BHR is presented. We associated an uncertainty of up to 2% with the retrieval of area averaged BHR, independently of flight altitudes and the BRF model used for the inversion. As expected, the local nature of PARABOLA data is revealed by the difference of the anisotropic kernel parameters with the corresponding parameters retrieved from aircraft loops. The uncertainty of the resultant BHR fell within .