In the era of globalisation, decreasing synthetic resources, especially petroleum, have encouraged global communities to apply biomass waste as a substitute material for green technology development. The development of plastic products from lignocellulosic fibre-reinforced composites has been a hot topic among material scientists and engineers due to their abundance, sustainable in nature, and less toxic towards health. For the Malaysian scenario, sugar palm is a plant found in the wild and locally planted in certain areas in Malaysia and Indonesia. Generally, sugar palm can be harvested for traditional foods, fruits, starch sugar (gula kabung), and alcohol, whereas sugar palm fibre (SPF) is used in conventional products (brushes and brooms). Various researchers are working on the characterisation of fibre and its composites for engineering and packaging products. The main drawback of SPF is its hydrophilic behaviour, which leads to high moisture uptake and inhibits a good bond between the fibre and the matrix. Thus, a solution for this problem is by implementing chemical treatments on the fibre. From the literature review, no comprehensive review paper has been published on the influence of chemical treatment on the mechanical behaviour of SPF-reinforced polymer composites. Thus, the present review examines recent studies on the mechanical properties of sugar palm lignocellulosic fibres with various chemical treatments to evaluate their potential in structural applications.

Urbanization is growing rapidly in Malaysia. Rapid urbanization has known to have several negative impacts towards hydrological cycle due to decreasing of pervious area and deterioration of water quality in stormwater runoff. One of the negative impacts of urbanization is the congestion of the stormwater drainage system and this situation leading to flash flood problem and water quality degradation. There are many urban stormwater management softwares available in the market such as Storm Water Drainage System design and analysis program (DRAINS), Urban Drainage and Sewer Model (MOUSE), InfoWorks River Simulation (InfoWork RS), Hydrological Simulation Program-Fortran (HSPF), Distributed Routing Rainfall-Runoff Model (DR3M), Storm Water Management Model (SWMM), XP Storm Water Management Model (XPSWMM), MIKE-SWMM, Quality-Quantity Simulators (QQS), Storage, Treatment, Overflow, Runoff Model (STORM), and Hydrologic Engineering Centre-Hydrologic Modelling System (HEC-HMS). In this paper, we are going to discuss briefly about several softwares and their functionality, accessibility, characteristics and components in the quantity analysis of the hydrological design software and compare it with MSMA Design Aid and Database. Green Infrastructure (GI) is one of the main topics that has widely been discussed all over the world. Every development in the urban area is related to GI. GI can be defined as green area build in the develop area such as forest, park, wetland or floodway. The role of GI is to improve life standard such as water filtration or flood control. Among the twenty models that have been compared to MSMA SME, ten models were selected to conduct a comprehensive review for this study. These are known to be widely accepted by water resource researchers. These ten tools are further classified into three major categories as models that address the stormwater management ability of GI in terms of quantity and quality, models that have the capability of conducting the economic analysis of GI and models that can address both stormwater management and economic aspects together.

Pultruded glass fibre reinforced polymer (pGFRP) composites provide outstanding properties for composite polymer cross arms in power transmission line applications. This study has investigated the effects of various stacking sequences of fibres directions of pGFRP on flexural strength and creep behaviour. The use of static four-point bending flexural tests revealed that Stacking Sequence 2 (±45/0/90/0/90/0) had a significant flexural strength of 399.9 MPa while Stacking Sequence 1 (±45/90/0/±45) had a flexural strength of 242.5 MPa. Furthermore, the four-point bending creep experiments were performed at three distinct stress levels, notably 12%, 24%, and 37% of the ultimate flexural strength, to characterise the creep behaviour of distinct stacking sequences. Moreover, Findley’s power law equation for bending creep behaviour has revealed that the time-dependent reduction factor of Stacking Sequence 1 and Stacking Sequence 2 estimates a drop in flexural modulus of 23% and 10% respectively.

Concrete is brittle; hence, it is incredibly likely that concrete buildings may fail in both local and global ways under dynamic and impulsive stresses. An extensive review investigation was carried out to examine reinforced concrete (RC) slab behavior under low-velocity impact loading. Significant past research studies that dealt with experimental and numerical simulations and analytical modeling of the RC slabs under impact loading have been presented in this work. As a result, numerous attempts to define failure behavior and to assess concrete structures’ vulnerability to lateral impact loads have been made in the literature. Based on analytical, numerical, and experimental studies carried out in previous research, this article thoroughly reviewed the current state of the art regarding the responses and failure behaviors of various types of concrete structures and members subjected to low-velocity impact loading. The effects of different structural and load-related factors were examined regarding the impact strength and failure behavior of reinforced concrete slabs reinforced with various types of strengthening procedures and exposed to low-velocity impact loads. The reviews suggested that advanced composite materials, shear reinforcement, and hybrid techniques are promising for effectively strengthening concrete structures.

Pultruded glass-fibre reinforced polymer (pGFRP) composites are classified as lightweight material, which exhibit high strength-to-weight ratio for structural usage. This composite material has been applied as cross-arm members in transmission towers due to its ability in thermal and electrical insulation. However, the influence of the stacking sequence of pGFRP composite on its mechanical performance has not been fully covered in the literature to explain the long-term durability of the current cross-arm designs. The study expected to evaluate five fiber layers with various stacking sequences in terms of quasi-static and creep tests in a four-point bending mode. The creep test was performed for 1440 h (60 days). These composites were fabricated using the pultrusion process in the form of a square hollow structure. Later, it was cut into composite coupons with various sizes depending on the test conducted. The results showed that nine layers with 0°/45°/0°/−45°/0°/−45°/0°/45°/0° had the ultimate flexural strength. This stacking sequence configurations seemed to be optimally manufactured in continuous roving fibre by alternating between 0° and ±45° fiber orientations. Additionally, the S-9 pGFRP composite sample showed that it had a low-creep deflection with high elastic and apparent creep moduli in 1440 h. In terms of strength reduction factor, this configuration was recorded as the highest. The findings showed that the nine layers of pGFRP composites with alternation of 0° and ±45° fiber orientations were highly suitable for structural application at transmission towers for a long-term operation.