Fouzia Ferdous

Mrs. Fouzia Ferdous

Electrical &Electronic Engineering, Bangladesh University of Engineering and Technology, Dhaka, Bangladesh
orcid

Research Focus & Metrics

Academic Career Length

6Years (2021-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 June 2021 in International Journal of Power Electronics and Drive Systems (IJPEDS)
Verified
Journal Article
Open access
FFFouzia Ferdous
Fouzia Ferdous
ARABM Harun-ur Harun-ur Rashid
ABM Harun-ur Harun-ur Rashid
Light emitting diodes (LEDs) are current driven devices. So, it is essential to maintain the stability of LED voltage and current. Variation of temperature may cause of instabilities and bifurcations in the LED driver. Driving LEDs from an offline power source faces design challenges like it have to maintain low harmonics in input current, to achieve high power factor, high efficiency and to maintain constant LED current and to ensure long lifetime. This paper proposes the technique of harmonics reduction by using parametric optimization of Single ended primary inductor converter (SEPIC) based LED driver. Without optimization of SEPIC parameters input energy will not be properly transferred to the load and this un-transferred energy will be transmitted to the source. Consequently, the quality of input current will be hampered i.e. harmonics will contaminate the input current. Focussing this, the paper has presented the design of a non-isolated integrated-stage single-switch constant current LED driver operating in discontinuous conduction mode (DCM) in SEPIC incorporating the design of control circuit with soft start mechanism. This LED driver has achieved a good efficiency (90.6%) and high-power factor (0.98) with reduced harmonics (3.35%). System stability has been determined and simulation studies are performed to confirm the validity of the LED driver circuit. A laboratory prototype is built.

1 December 2022 in Electronics
Verified
Journal Article
Open access
PDF file
FFFouzia Ferdous
Fouzia Ferdous
ARABM Harun-ur Harun-ur Rashid
ABM Harun-ur Harun-ur Rashid
There are some challenges involved in the design of a multicolor LED driver, such as the precise control of color consistency, i.e., maintaining the correlated color temperature (CCT) and luminous intensity. CCT deviation causes a color shift of composite light. This paper approaches the method of nonlinear optimization of the LED currents of two LED sources to achieve the desired CCT. A bicolor blended-shade white LED system is formed by using a warm color LED source of 1000 K CCT and a cool color LED source of 6500 K CCT. By using a nonlinear optimization methodology, the reduced deviation of the blended CCT and optimum LED currents are obtained. The optimized currents in the two LED strings are maintained by the control circuit of the single-ended primary inductor converter (SEPIC). The obtained reduced deviation of the CCT is 43 K, and the precision is 99.15%. Again, harmonics in the input current hamper power quality, i.e., reduce the power factor and increase power loss. This paper proposes the harmonic reduction technique to achieve the lowest value of total harmonic distortion (THD) through the nonlinear parametric optimization of the SEPIC. Measured THD = 4.37%; PF = 0.96; and efficiency = 92.8%. The system stability was determined and found to be satisfactory.

11 September 2024 in Journal of Electrical and Electronic Engineering
Verified
Journal Article
Open access
PDF file
FFFouzia Ferdous
Fouzia Ferdous
ARABM Harun-ur Harun-ur Rashid
ABM Harun-ur Harun-ur Rashid
LED-powered luminaires have the ability to offer cutting-edge features like temperature adjustment and color management. Color shift creates discomfort in human eyes. So it is essential to design a LED driver which will precisely control the color parameters of the LED driver. Precise control of color parameters like CRI, CCT, color intensity is very complex and challenging. This paper describes the nonlinear optimization methodology for the design of blended LED light sources. This paper presents the methodology that enables LED strings regarding various parameters, e.g. high color rendering index (CRI) and high luminous efficacy of a blended bi-color (namely red CCT-2500K and blue CCT-9000K) LED driving system. Due to the applied optimization, the obtained CRI is maintained 98.03%. The overall luminous intensity depends upon the combined luminous flux which depends upon the current control of both LED sources. These optimized LED currents ensure the desired CCT. The achieved luminous efficacy is 90% at two optimal peak wavelengths 601 nm and 426 nm respectively. Power loss is minimized by frequency optimization. At the same time power parameters i.e. low THD and high P. F. is also maintained. The nonlinear optimization is verified in Ltspice simulations and experimentally for two different luminaire strings.