Ghandy Lamaa

Dr. Ghandy Lamaa

Civil Engineering, Architecture and Environment, Universidade de Lisboa - Instituto Superior Tecnico, Lisbon, Lisboa, Portugal
orcid

Research Focus & Metrics

Academic Career Length

5Years (2022-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
13 April 2023 in Materials
Verified
Journal Article
Open access
PDF file
Ghandy LamaaGhandy Lamaa
Ghandy Lamaa
António P.C. DuarteAntónio P.C. Duarte
António P.C. Duarte
Rui Vasco SilvaRui Vasco Silva
Rui Vasco Silva
Jorge De BritoJorge De Brito
Jorge De Brito
This paper presents a literature review on the effects of accelerated carbonation on alkali-activated materials. It attempts to provide a greater understanding of the influence of CO2 curing on the chemical and physical properties of various types of alkali-activated binders used in pastes, mortars, and concrete. Several aspects related to changes in chemistry and mineralogy have been carefully identified and discussed, including depth of CO2 interaction, sequestration, reactions with calcium-based phases (e.g., calcium hydroxide and calcium silicate hydrates and calcium aluminosilicate hydrates), as well as other aspects related to the chemical composition of alkali-activated materials. Emphasis has also been given to physical alterations such as volumetric changes, density, porosity, and other microstructural properties caused by induced carbonation. Moreover, this paper reviews the influence of the accelerated carbonation curing method on the strength development of alkali-activated materials, which has been awarded little attention considering its potential. This curing technique was found to contribute to the strength development mainly through decalcification of the Ca phases existing in the alkali-activated precursor, leading to the formation of CaCO3, which leads to microstructural densification. Interestingly, this curing method seems to have much to offer in terms of mechanical performance, making it an attractive curing solution that can compensate for the loss in performance caused by less efficient alkali-activated binders replacing Portland cement. Optimising the application of such CO2-based curing methods for each of the potential alkali-activated binders is recommended for future studies for maximum microstructural improvement, and thus mechanical enhancement, to make some of the “low-performing binders” adequate Portland cement substitutes.

5 February 2022 in Applied Sciences
Verified
Journal Article
Open access
PDF file
Dany KassimDany Kassim
Dany Kassim
Ghandy LamaaGhandy Lamaa
Ghandy Lamaa
Rui Vasco SilvaRui Vasco Silva
Rui Vasco Silva
Jorge De BritoJorge De Brito
Jorge De Brito
The use of electric arc furnace slag (EAFS) as sole precursor to produce alkali-activated mortars has been experimentally investigated. EAFS, a by-product of the steel recycling industry, is a coarse material with unevenly distributed and size-extensive particles. Milling of EAFS was required to achieve a cement-like sized powder before it could be used as precursor. Different combinations of sodium hydroxide (NaOH) and sodium silicate (Na2SiO3) were used, by varying the Na2O/binder concentration (4%, 6%, 8%, 10%, 12%) and SiO2/Na2O ratio (0, 0.5, 1.0, 1.5, 2.0, 2.5) to maximize the mechanical performance. The alkaline solutions were prepared 24 h prior to mixing to unify temperatures for all mixes. The results showed that the SiO2/Na2O ratio and strength development are directly proportional. The maximum 28-day compressive strength obtained, after being subjected to an initial 24 h thermal curing at 80 °C, was 9.1 MPa in mixes with 4% Na2O/binder and 2.5 SiO2/Na2O. However, after an additional 28 days of accelerated carbonation, the maximum compressive strength (i.e., 31 MPa compared to 3.9 MPa in uncarbonated mixes, corresponding to an 800% increase) was obtained in mixes with 12% and 1.0 for Na2O/binder and SiO2/Na2O, respectively, thus showing an alteration in the optimal alkaline activator contents.

22 March 2024 in Construction and Building Materials
Verified
Journal Article
Closed access
SASalem Alnezami
Salem Alnezami
Ghandy LamaaGhandy Lamaa
Ghandy Lamaa
MPManuel Francisco Costa Pereira
Manuel Francisco Costa Pereira
RKRawaz Kurda
Rawaz Kurda
Jorge De BritoJorge De Brito
Jorge De Brito
Rui Vasco SilvaRui Vasco Silva
Rui Vasco Silva

25 February 2023 in Materials
Verified
Journal Article
Open access
PDF file
Ghandy LamaaGhandy Lamaa
Ghandy Lamaa
DSDavid Suescum-Morales
David Suescum-Morales
António P.C. DuarteAntónio P.C. Duarte
António P.C. Duarte
Rui Vasco SilvaRui Vasco Silva
Rui Vasco Silva
Jorge De BritoJorge De Brito
Jorge De Brito
Three industrial aluminosilicate wastes were studied as precursors to produce alkali-activated concrete: (i) electric arc furnace slag, (ii) municipal solid waste incineration bottom ashes, and (iii) waste glass rejects. These were characterized via X-ray diffraction and fluorescence, laser particle size distribution, thermogravimetric, and Fourier-transform infrared analyses. Distinctive combinations of anhydrous sodium hydroxide and sodium silicate solution were tried by varying the Na2O/binder ratio (8%, 10%, 12%, 14%) and SiO2/Na2O ratio (0, 0.5, 1.0, 1.5) to find the optimum solution for maximized mechanical performance. Specimens were produced and subjected to a three-step curing process: (1) 24 h thermal curing (70 °C), (2) followed by 21 days of dry curing in a climatic chamber (~21 °C, 65% RH), and (3) ending with a 7-day carbonation curing stage (5 ± 0.2% CO2; 65 ± 10% RH). Compressive and flexural strength tests were performed, to ascertain the mix with the best mechanical performance. The precursors showed reasonable bonding capabilities, thus suggesting some reactivity when alkali-activated due to the presence of amorphous phases. Mixes with slag and glass showed compressive strengths of almost 40 MPa. Most mixes required a higher Na2O/binder ratio for maximized performance, even though, contrary to expectations, the opposite was observed for the SiO2/Na2O ratio.

29 September 2024 in Construction and Building Materials
Verified
Journal Article
Open access
AMAntonio Manuel Merino-Lechuga
Antonio Manuel Merino-Lechuga
Ghandy LamaaGhandy Lamaa
Ghandy Lamaa
Rui Vasco SilvaRui Vasco Silva
Rui Vasco Silva
Jorge De BritoJorge De Brito
Jorge De Brito
JJJosé Ramón Jiménez
José Ramón Jiménez
AGAgata Gonzaleez
Agata Gonzaleez

17 June 2025 in Construction and Building Materials
Verified
Journal Article
Open access
ALAntonio Manuel Merino Lechuga
Antonio Manuel Merino Lechuga
Ghandy LamaaGhandy Lamaa
Ghandy Lamaa
RSRui Vasco Silva
Rui Vasco Silva
JBJorge de Brito
Jorge de Brito
JJJosé Ramón Jiménez
José Ramón Jiménez
ÁGÁgata González-Caro
Ágata González-Caro