Ma. Guadalupe Plaza

Ms. Ma. Guadalupe Plaza


Research Focus & Metrics

Academic Career Length

3Years (2024-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
8 April 2024 in Polymers
Verified
Journal Article
Open access
PDF file
Ma. Guadalupe PlazaMa. Guadalupe Plaza
Ma. Guadalupe Plaza
MLMaria Luisa Mendoza López
Maria Luisa Mendoza López
José de Jesús Pérez BuenoJosé de Jesús Pérez Bueno
José de Jesús Pérez Bueno
JMJoaquín Pérez Meneses
Joaquín Pérez Meneses
APAlejandra Xochitl Maldonado Pérez
Alejandra Xochitl Maldonado Pérez
A plastic injection waste known as “purge” cannot be reintegrated into the recycling chain due to its shape, size, and composition. Grinding these cannot be carried out with traditional mills due to significant variations in size and shape. This work proposes a process and the design of a device that operates with solar energy to cut the purges without exceeding the degradation temperature. The size reduction allows reprocessing, revalorization, and handling. The purges are mixtures of processed polymers, so their characterization information is unavailable. Some characterizations were conducted before the design of the process and after the cut of the purges. Some of the most representative purges in a recycling company were evaluated. The flame test determines that all material mixtures retain thermoplasticity. The hardness (Shore D) presented changes in four of the purges being assessed, with results in a range of 59–71 before softening and 60–68 after softening. Young’s modulus was analyzed by the impulse excitation technique (IET), which was 2.38–3.95 GPa before softening and 1.7–4.28 after softening. The feasibility of cutting purges at their softening temperature was evaluated. This was achieved in all the purges evaluated at 250–280 °C. FTIR allowed for corroboration of no significant change in the purges after softening. The five types of purges evaluated were polypropylene-ABS, polycarbonate-ABS-polypropylene, yellow nylon 66, acetal, and black nylon 66 with fillers, and all were easily cut at their softening temperature, allowing their manipulation in subsequent process steps.

5 March 2026 in Recycling
Verified
Journal Article
Open access
PDF file
Ma. Guadalupe PlazaMa. Guadalupe Plaza
Ma. Guadalupe Plaza
MLMaria Luisa Mendoza López
Maria Luisa Mendoza López
José de Jesús Pérez BuenoJosé de Jesús Pérez Bueno
José de Jesús Pérez Bueno
EMEdain Belén Pérez Mendoza
Edain Belén Pérez Mendoza
MRMartha Elva Perez Ramos
Martha Elva Perez Ramos
Injection-molding purges are heterogeneous, bulky residues whose uncertain composition and irregular geometry hinder direct reinsertion, making cold shredding costly and maintenance-intensive. This work develops a low-infrastructure solar-assisted pre-processing route using a PMMA Fresnel lens to induce controlled sub-onset softening and enable clean shear cutting without destructive thermal histories. The sub-onset softening is here defined into a viscoelastically active range (at or above Tg for the amorphous phase) while remaining below the melting onset (Tm, onset) and below the onset of thermal degradation (Td, onset). The station was engineered via QFD and risk-oriented design tools, while a weighted Pugh matrix selected shear cutting over saw-based alternatives. A screening factorial DOE showed that lens height, angle, and their interaction significantly govern focal-spot diameter and receiver temperature, yielding linear relations for conservative set-point selection. Receiver benchmarking further indicated that copper reaches substantially higher temperatures than graphite under identical exposure conditions, supporting copper as the simplest, rapid-heating receiver. Under DOE-calibrated operation, tear-free shear cutting was achieved across representative purge families (PP–ABS, PC–ABS–PP, PA66, PA66-filler, and POM) without forced convection. From a recycling and waste-management perspective, the approach converts bulky purge scrap into mill-compatible feedstock with reduced mechanical resistance, lowering tool wear and fines generation, accelerating downsizing, and limiting stockpiling that elevates combustible-inventory fire risk. Overall, the proposed DOE-calibrated, operator-friendly framework improves recycling feasibility by enabling safer handling, more stable preprocessing throughput, and reduced reliance on disposal or long-term storage for heterogeneous industrial purges.