The present study evaluates the influence of the level of roasting and the grind size on the moisture content and repose angle of coffee during storage. Raw coffee beans (Coffea canephora and Coffea arabica), hulled and dried, were roasted to two different levels: medium light (SCAA#65) and moderately dark (SCAA#45). The beans were then ground into three different grind sizes: fine (0.59 mm), medium (0.84 mm) and coarse (1.19 mm). An additional coffee lot was kept whole. Following grinding, samples were stored at two different temperatures (10 and 30 ºC) and analyzed after five different storage durations (0, 30, 60, 120 and 180 days). The moderately dark roast was found to have a lower moisture content. Finely ground samples had higher angles of repose. It is concluded that the grind size, level of roasting and duration of storage significantly affect the moisture content and angle of repose of coffee.
13 May 2016 in Journal of Food Processing and Preservation
Roasting is one of the most complex coffee processing steps due to simultaneous transfers of heat and mass. During this process, beans lose mass because of fast physical and chemical changes that will set color and flavor of the commercial coffee beverage. Therefore, we aimed at assessing the kinetics of mass loss in commercially roasted coffee beans according to heating throughout the processing. For that, we used samples of 350-g Arabica coffee processed grains with water content of 0.1217 kga kg-1, in addition to a continuous roaster with firing gas. The roaster had initial temperatures of 285, 325, 345 and 380 °C, decreasing during the process up to 255, 285, 305 and 335 °C respectively. Mass loss was calculated by the difference between grain weight before and after roasting. We observed a linear variation directly dependent on roaster temperature. For each temperature during the process was obtained a constant mass loss rate, which was reported by the Arrhenius model with r2 above 0.98. In a roaster in non-isothermal conditions, the required activation energy to start the mass loss in a commercial coffee roasting index was 52.27 kJ mol -1.
1 January 2022 in Brazilian Journal of Food Technology
Flowability of agricultural products is an important factor to be considered at post-harvest, thus impacting directly on number of operations and the design of machinery. This study aimed to evaluate and determine the K coefficient and flow properties as a function of different levels of roasting, grain size, temperature and storage. Coffee beans were roasted at medium light and moderately dark, then ground at fine, medium and coarse sizes. An additional coffee lot was not ground. Samples were stored at 10 ºC and 30 ºC and analyzed during storage (0, 30, 60, 120 and 180 days), regarding internal and external friction coefficients, angle of internal friction, effective angle of internal friction, wall friction angle (concrete, rough steel and wood) and lateral pressure coefficient (K coefficient). Angle of internal friction varied significantly due to particle size and roast degree. Moderately dark roast with fine particle size led to higher values (about 29.5 º) of wall friction angle. The wood sample was the material with the highest values of wall friction angle, followed by the concrete and steel samples, when compared at the same storage temperature, roast degree and particle size. Whole coffee was classified as free-flowing. Fine particle size leads to cohesive flow characteristic, according to the flow function. Coffee roasted at medium light, kept whole requires storage facilities with higher pressure support, accordingly to the K coefficient values.
El coco es una fruta que puede aprovecharse completamente desde su parte líquida hasta su parte sólida, considerando la parte alimenticia y los residuos. La parte sólida puede utilizarse directamente como alimento, también puede ser procesado para su uso posterior. El secado es un proceso necesario para su conservación, por lo tanto se evaluó el secado por radiación para establecer la relación entre rapidez y temperatura del proceso. Se utilizaron las temperaturas de 60, 80,100 y 120 °C. El coco fue extraído, molido y homogenizado manualmente. Se utilizó un deshidratador con transmisión de calor por radiación en cuatro temperaturas de proceso. El contenido de humedad fue determinado por la pérdida de masa hasta obtener peso constante en una capa delgada de producto. Se determinó que durante secado, el contenido de humedad es exponencialmente decreciente y el modelo matemático de Midilli se ajustó adecuadamente con un coeficiente de determinación (R2) mayor al 94 %. El efecto de la temperatura en la rapidez del proceso se ajustó con la ecuación de Arrhenius. Se determinó que la energía de activación del proceso de secado por radiación en coco fue de 60,7 kJ/mol. La relación matemática de la rapidez del secado es una doble exponencial que depende directamente de la temperatura y el tiempo de secado.
About Me
Drying, storage, roasting and quality of agricultural products.
Drying, storage, roasting and quality of agricultural products.