Rotor vibration control is crucial for the reliability of rotating machines. This article applies active vibration control to reduce the vibration of a rotor bearing system using flexible piezoelectric patches as actuators mounted on the shaft external surface. The patches reduce the vibration due to unbalance forces by generating bending moments to counteract rotor deformation. An active vibration control system is designed based on a full-state linear quadratic regulator controller. Since proximity probes are used to measure the lateral vibrations of the rotor at few shaft positions, an observer is designed to estimate the unmeasured vibrations. The weighting matrices required by the linear quadratic regulator controller are selected by trial and error so that the displacement amplitudes are reduced to a minimum and the actuation voltages remain within the limitations defined by the manufacturer of the used patches. Simulated responses demonstrate the effectiveness of the designed controller in attenuating the lateral vibration of the rotor bearing system when using two actuating voltages. The vibration response is reduced for the steady-state condition and during run-up particularly at the first critical speed.
This paper proposes a vibration identification method based on a Genetic Algorithm (GA) to improve the reliability of rotating machinery by effectively controlling rotor vibrations. The classical active control approach, known as the Linear Quadratic Regulator (LQR) control algorithm, is influential in this regard but heavily depends on specific parameters. However, using a predetermined set of parameters may not suffice to address the diverse vibration control needs of different rotating systems. To address this issue, an active vibration control system employing flexible piezoelectric patches attached to the external surface of the rotating shaft, functioning as actuators, is designed. These patches are individually supplied with actuation voltages. Through a numerical example, the effectiveness of the proposed system is validated. The numerical results demonstrate a significant reduction of the amplitude of the unbalance response, with a reduction of 79% at the first critical speed during a steady-state condition and 75% during run-up. The numerical findings underscore the effectiveness of the proposed control strategy (LQR-GA), highlighting its notable dynamic impact compared to the conventional LQR algorithm with fixed parameters.
This paper presents a comprehensive methodology for the optimal placement of piezoelectric patches on the shaft surface of a rotor bearing system to apply active vibration control. The placement strategy based on the Modal Strain Energy (MSE) method is used to identify the locations along the shaft where the modal deformation energy is maximum at the operating rotor speeds. This approach is particularly effective for multimodal control, as the MSE distribution can be evaluated for different mode shapes to ensure the actuators have significant authority over multiple critical resonances. To fully exploit this optimal placement, a Linear Quadratic Regulator (LQR) is employed to compute feedback gains that minimize a quadratic cost function balancing displacement reduction and control effort. The finite element method is applied to model a rotor bearing system composed of a flexible shaft and rigid disks. The rotor is actively controlled using piezoelectric patches bonded on selected locations on the shaft. An LQR controller is used to provide feedback signals for multiple piezoelectric patch pairs. The optimal weighting matrices of the controller are selected using the Genetic Algorithm (GA) to improve the effectiveness of the system. The control signals are transmitted to the patches via multipath slip rings. Simulation results for the steady state vibration response for a selected range of excitation frequencies show that significant vibration reductions of up to 86% and 90% are achieved, respectively, at the first and second critical speeds for the considered case study. The case study shows that the integrated optimization approach based on the MSE method proves to be effective and computationally efficient.
This paper presents an optimization-based framework for active vibration control of rotor bearing systems using external surface-bonded piezoelectric patches. The rotor bearing system is modelled using the Finite Element Method (FEM), enabling the coupling between the shaft and the flexible piezoelectric actuators. A Linear Quadratic Regulator (LQR) is adopted to achieve optimal feedback control considering the balance between vibration reduction and control effort. The central contribution of this work is a comprehensive actuator placement optimization of the axial and angular position of the piezoelectric patches along the shaft. Firstly, axial positions are selected by maximizing a multimodal weighted Modal Strain Energy (MSE) criterion over a selected number of bending modes. In the second stage, which constitutes the main novelty of this work, the angular position of each pair of bonded piezoelectric patches is optimized. Each piezoelectric pair generates control moments at each extremity of the patch. The influence of the angular separation between independent piezoelectric pairs bonded at different axial locations is investigated through an iterative optimization framework. The optimized actuator placements are subsequently employed within an LQR-based active vibration control framework. The parameters of the controller are selected using a Genetic Algorithm (GA). Numerical simulations are performed on a bi-disk flexible rotor bearing system. The results of the numerical simulations demonstrate that the combined axial-circumferential optimization significantly enhances the controllability of the rotor system and improves the multimodal vibration suppression capability, achieving an improvement of approximately 93%. The proposed methodology offers a physically meaningful and computationally efficient framework, guaranteeing symmetric and effective vibration control.