Mnaouar Chouchane

Dr. Mnaouar Chouchane

orcid

Research Focus & Metrics

Academic Career Length

21Years (2006-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
11 April 2006 in International Journal for Numerical Methods in Engineering
Verified
Journal Article
Closed access
PDF file
NGNajeh Guedria
Najeh Guedria
HSHichem Smaoui
Hichem Smaoui
MCMnaouar Chouchane
Mnaouar Chouchane

25 November 2017
Verified
Book Chapter
Closed access
PDF file
Rabie ALOUIRabie ALOUI
Rabie ALOUI
WLWalid Larbi
Walid Larbi
MCMnaouar Chouchane
Mnaouar Chouchane

6 May 2022 in Smart Materials and Structures
Verified
Journal Article
Closed access
FSFaiza Sakly
Faiza Sakly
MCMnaouar Chouchane
Mnaouar Chouchane
Smart materials are widely used for vibration control of rotating machines. This paper considers the control of vibration of a bi-disk rotor bearing system using electro-rheological elastomer (ERE) rings inserted in the bearings. The bi-disk rotor is selected so that vibration response can be studied in a rotating speed range which includes the first two critical speeds. The rotor bearing system is modelled using the finite element method taking into account the gyroscopic effect of the rotor and the internal damping of the shaft. The influence of the active elastomer when it is subjected to different levels of the electric field on the critical speeds is first investigated. Then, the vibration response is determined for both steady-state and transient running up and running down conditions. Simulation results show the potentials of the ERE when used in passive mode for vibration reduction in the steady-state and transient running up and down conditions of the rotor system. In the active mode, the application of an electric field to the EREs shifts slightly the resonant speeds to higher frequencies due to the increase of the stiffness of the bearings while increasing the vibration amplitudes in the steady-state and transient running up and down conditions in the vicinity of the resonant speeds. Nevertheless, it has been shown that the rotor steady-state vibration response can be reduced at other rotating speed range when an electric field is applied.


1 January 2012
Verified
Book Chapter
Closed access
PDF file
Ezzeddine FtoutouEzzeddine Ftoutou
Ezzeddine Ftoutou
MCMnaouar Chouchane
Mnaouar Chouchane
NBNoureddine Besbès
Noureddine Besbès

15 April 2026 in Engineering Research Express
Verified
Journal Article
Closed access
Maryem BrahemMaryem Brahem
Maryem Brahem
MCMnaouar Chouchane
Mnaouar Chouchane
This paper presents a comprehensive methodology for the optimal placement of piezoelectric patches on the shaft surface of a rotor bearing system to apply active vibration control. The placement strategy based on the Modal Strain Energy (MSE) method is used to identify the locations along the shaft where the modal deformation energy is maximum at the operating rotor speeds. This approach is particularly effective for multimodal control, as the MSE distribution can be evaluated for different mode shapes to ensure the actuators have significant authority over multiple critical resonances. To fully exploit this optimal placement, a Linear Quadratic Regulator (LQR) is employed to compute feedback gains that minimize a quadratic cost function balancing displacement reduction and control effort. The finite element method is applied to model a rotor bearing system composed of a flexible shaft and rigid disks. The rotor is actively controlled using piezoelectric patches bonded on selected locations on the shaft. An LQR controller is used to provide feedback signals for multiple piezoelectric patch pairs. The optimal weighting matrices of the controller are selected using the Genetic Algorithm (GA) to improve the effectiveness of the system. The control signals are transmitted to the patches via multipath slip rings. Simulation results for the steady state vibration response for a selected range of excitation frequencies show that significant vibration reductions of up to 86% and 90% are achieved, respectively, at the first and second critical speeds for the considered case study. The case study shows that the integrated optimization approach based on the MSE method proves to be effective and computationally efficient.