Jamarosliza Jamaluddin

Dr. Jamarosliza Jamaluddin

Department of Chemical Engineering, School of Chemical & Energy Engineering
+1
orcid

Research Focus & Metrics

Academic Career Length

8Years (2019-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
1 November 2021 in Journal of Environmental Management
Verified
Journal Article
Closed access
CBCassendra Phun Chien Bong
Cassendra Phun Chien Bong
MAMuhd Nazrul Hisham Zainal Alam
Muhd Nazrul Hisham Zainal Alam
SSSani Amril Samsudin
Sani Amril Samsudin
Jamarosliza JamaluddinJamarosliza Jamaluddin
Jamarosliza Jamaluddin
NANadia Adrus
Nadia Adrus
BCBahrul Razha Bin Chuprat
Bahrul Razha Bin Chuprat

2 December 2021 in Environmental Quality Management
Verified
Journal Article
Closed access
PDF file
VLVictor Wei Xiang Lai
Victor Wei Xiang Lai
Jamarosliza JamaluddinJamarosliza Jamaluddin
Jamarosliza Jamaluddin
NNNur Aina Farhana Mat Nasir
Nur Aina Farhana Mat Nasir
NBNorfhairna Baharulrazi
Norfhairna Baharulrazi
RMRohah A. Majid
Rohah A. Majid
NANadia Adrus
Nadia Adrus

4 February 2021 in Polymers
Verified
Journal Article
Open access
PDF file
SGSiti Khairunisah Ghazali
Siti Khairunisah Ghazali
NANadia Adrus
Nadia Adrus
RMRohah A. Majid
Rohah A. Majid
Fathilah AliFathilah Ali
Fathilah Ali
Jamarosliza JamaluddinJamarosliza Jamaluddin
Jamarosliza Jamaluddin
The elimination of mercury, low energy consumption, and low heat make the ultraviolet light-emitting diode (UV-LED) system emerge as a promising alternative to conventional UV-mercury radiation coating. Hence, a series of hydrophobic coatings based on urethane acrylate oligomer and fluorinated monomer via UV-LED photopolymerisation was designed in this paper. The presence of fluorine component at 1160 cm−1, 1235 cm−1, and 1296 cm−1 was confirmed by Fourier Transform Infra-Red spectroscopy. A considerably high degree C=C conversion (96–98%) and gel fraction (95–93%) verified the application of UV-LED as a new technique in radiation coating. It is well-accepted that fluorinated monomer can change the surface wettability as the water contact angle of the coating evolved from 88.4° to 121.2°, which, in turn, reduced its surface free energy by 70.5%. Hence, the hydrophobicity of the coating was governed by the migration of the fluorine component to the coating surface as validated by scanning electron and atomic force microscopies. However, above 4 phr of fluorinated monomer, the transparency of the cured coating examined by UV-visible spectroscopy experienced approximately a 16% reduction. In summary, the utilisation of UV-LED was a great initiative to develop green aspect in photopolymerisation, particularly in coating technology.

23 October 2024 in ChemistrySelect
Verified
Journal Article
Closed access
NNNur Aina Farhana Mat Nasir
Nur Aina Farhana Mat Nasir
CWChang Koon Wong
Chang Koon Wong
Jamarosliza JamaluddinJamarosliza Jamaluddin
Jamarosliza Jamaluddin
NANadia Adrus
Nadia Adrus

24 June 2019 in Journal of Photopolymer Science and Technology
Verified
Journal Article
Open access
PDF file
SGSiti Khairunisah Ghazali
Siti Khairunisah Ghazali
FAFatria Syaimima Syaiful Azim
Fatria Syaimima Syaiful Azim
NANadia Adrus
Nadia Adrus
Jamarosliza JamaluddinJamarosliza Jamaluddin
Jamarosliza Jamaluddin
This paper presents the effect of UV-LED and UV-mercury as the light source toward curing behaviour of urethane acrylate coating. The UV-curable coating was prepared based on aliphatic urethane acrylate oligomer, 2-ethylhexyl acrylate (2-EHA), methyl methacrylate (MMA), trimethylolpropane triacrylate (TMPTA), and commercial photoinitiator. The effect of irradiation time on curing behaviour was investigated using Fourier Transform Infra-Red (FTIR) and the percentage of C=C conversion was calculated. From the ATR-FTIR spectra, the C=C absorption peak at 810 cm-1 and 1635 cm-1 was found to be decreased after UV irradiation, indicated the proceeding of the polymerisation reaction. In term of C=C conversion, UV-LED irradiation showed better results with 97-99% than UV-mercury irradiation which is 86-96%. It was also observed that the tackiness of the coating reduced via UV-LED irradiation, suggesting higher conversion of monomers. Gel fraction of the coating also measured and higher gel fraction values, > 98% in this study was associated with higher cross-linking density. The results of this study depicted that UV-LED is a viable alternative to replace UV-mercury-based lamp in the coating industry.

11 March 2022 in Environmental Quality Management
Verified
Journal Article
Closed access
WSWan Sarah Qistina Wan Ahmad Sofian
Wan Sarah Qistina Wan Ahmad Sofian
NBNorfhairna Baharulrazi
Norfhairna Baharulrazi
NYNor Alafiza Yunus
Nor Alafiza Yunus
SMSiti Fatimah Masturah Musa
Siti Fatimah Masturah Musa
NANadia Adrus
Nadia Adrus
Jamarosliza JamaluddinJamarosliza Jamaluddin
Jamarosliza Jamaluddin