This study investigates the impact of unsteady aerodynamic loads on the behavior of car dynamics during braking maneuvers. In the analysis, two independent solvers were coupled to solve an existing fluid structure interaction (FSI) problem. Transient CFD analysis applying Fluent software was used to obtain realistic aerodynamic loads. A full car, nonlinear dynamic model with elastic suspension system was built in a dedicated multibody dynamic system MSC.Adams/Car. Both physics were integrated into one ecosystem via a block diagram environment for multidomain simulation (Matlab/Simulink). Methodology elements were validated against experimental results for a rectangular beam in cross-flow with vortex-induced vibrations. The final results were validated against a full-scale experiment on a real car. The solution of an untypical flow problem (decreasing car speed during a braking maneuver) required an untypical reference frame. The classic case, with an observer at rest (stationary model and moving air), was replaced with a moving observer. The whole domain was translocated during the analysis with a velocity which varied with time. The problem was further complicated by the presence of movable aerodynamic elements. The overset mesh technique was used to allow movement of the car body and active aerodynamic surfaces. The results obtained show the importance of aerodynamic effects on the braking process. It was shown that in the analyzed scenario, movable aerodynamic features can reduce the distance to stop by 6%. The complex interaction between the active aerodynamic surface and the car body with respect to load split is discussed as well. The methodology proposed to determine the behavior car dynamics with unsteady aerodynamic effects taken into account appears to be a significant improvement when compared with existing methodologies used for such an assessment.
In the case of road cars, road safety is the primary factor. The geometry of high-speed road cars has no regulatory restrictions. In addition to the high engine power and effective shape, they can use various types of additional movable aerodynamic elements to adjust their aerodynamic characteristics to the road conditions. Based on the geometry of a two-seater prototype of such a vehicle, a numerical analysis of the influence of a number of additional movable aerodynamic elements on its aerodynamic characteristics was performed. Several of them were installed on the prototype. An electronic system recording a number of motion parameters of the entire car body and some of its movable elements installed on the body was designed and built. The system has been adapted to program the motion of additional aerodynamic elements according to the set algorithms of their activation, temporarily changing the aerodynamic characteristics of the car. An experimental study of the effect of changes in the aerodynamic characteristics of the prototype on its dynamic properties during a drive through a test road section was carried out. It was shown to what extent an average driver can increase the safe speed of the curve of the road using the possibilities of moving aerodynamic elements installed on it.
The relationship between the presented work and energy conservation is direct and indirect. Most of the literature related to energy-saving focuses on reducing the aerodynamic drag of cars, which typically leads to the appearance of vehicle motion instabilities at high speeds. Typically, this instability is compensated for by moving aerodynamic body components activated above a certain speed and left in that position until the vehicle speed drops. This change in vehicle configuration results in a significant increase in drag at high velocities. The presented study shows a fully coupled approach to fluid–structure interaction analyses of a car during a high-speed braking-in-turn manoeuvre. The results show how the aerodynamic configuration of a vehicle affects its dynamic behaviour. In this work, we used a novel approach, combining Computational Fluid Dynamics (CFD) analysis with the Multibody Dynamic System. The utilisation of an overset technique allows for car movement in the computational domain. Adding Moving Reference Frame (MRF) to this motion removes all restrictions regarding car trajectory and allows for velocity changes over time. We performed a comparative analysis for two aerodynamic configurations. In the first one, a stationary rear airfoil was in a base position parallel to a trunk generating low drag. No action of the driver was assumed. In the second scenario, brake activation initiates the rotation of the rear airfoil reaching in 0.1 s final position corresponding to maximum aerodynamic downforce generation. Also, no action of the driver was assumed. In the second scenario, the airfoil was moving from the base position up to the point when the whole system approached its maximum downforce. To determine this position, we ran a separated quasi-steady analysis in which the airfoil was rotating slowly to avoid transient effects. The obtained results show the importance of the downforce and load balance on car stability during break-in-turn manoeuvres. They also confirm that the proposed methodology of combining two independent solvers to analyse fluid–structure phenomena is efficient and robust. We captured the aerodynamic details caused by the car’s unsteady movement.
3 February 2019 in Journal of Advanced Transportation
The aim of this study was to extend the safety limits of fast moving cars by the application, in a controlled way, of aerodynamic forces which increase as the square of a car’s velocity and, if left uncontrolled, dramatically reduce car safety. This paper presents the methods, assumptions, and results of numerical and experimental investigations by modeling and simulation of the aerodynamic characteristics and dynamics of a small sports car equipped with movable aerodynamic elements operated by an electronic subsystem for data acquisition and aerodynamics active automatic control.