In the case of road cars, road safety is the primary factor. The geometry of high-speed road cars has no regulatory restrictions. In addition to the high engine power and effective shape, they can use various types of additional movable aerodynamic elements to adjust their aerodynamic characteristics to the road conditions. Based on the geometry of a two-seater prototype of such a vehicle, a numerical analysis of the influence of a number of additional movable aerodynamic elements on its aerodynamic characteristics was performed. Several of them were installed on the prototype. An electronic system recording a number of motion parameters of the entire car body and some of its movable elements installed on the body was designed and built. The system has been adapted to program the motion of additional aerodynamic elements according to the set algorithms of their activation, temporarily changing the aerodynamic characteristics of the car. An experimental study of the effect of changes in the aerodynamic characteristics of the prototype on its dynamic properties during a drive through a test road section was carried out. It was shown to what extent an average driver can increase the safe speed of the curve of the road using the possibilities of moving aerodynamic elements installed on it.
Crosswind action on a train poses a risk of vehicle overturning or derailment. To assess if new train designs fulfill the safety requirements, computational fluid dynamics is commonly used. This article presents a comprehensive wind flow analysis on an example of a TGV high-speed train. Large yaw angle range is studied with the application of widely used Reynolds-averaged Navier–Stokes (RANS) turbulence models. The predictive performance of popular RANS-based models in that regime has not been reported extensively before. The context of simulations is a study of crosswind stability using methodology presented in norm EN 14067-6:2018. It is shown that for yaw angles up to 45 degrees, aerodynamic forces predicted by all the studied RANS-based models are consistent with experimental data. At larger yaw angles, flow structure becomes complicated, separation lines are no longer defined by geometry, and significant discrepancies between turbulence models appear, with relative differences between models up to 30%. A detailed study was performed to investigate differences between turbulence models for specific angles of 40, 60, and 80 degrees, which correspond to distinctive ranges of moment characteristics. Finally, a successful attempt was made to tune a GEKO turbulence model to fit the experimental data. This allowed us to reduce the maximum relative error in comparison to the experiment in the full yaw angles range down to 12.7%, which is in line with the norm requirements.
Nowadays, aerodynamics is a key focal point in the vehicle design process. Beyond its direct impact on the performance of a vehicle, it also has significant effects on economics and safety. In the last decade numerical methods, mainly Computational Fluid Dynamics (CFD), have established themselves as a reliable tool that assists in the design process and complements classical tunnel tests. However, questions remain about the possible obtained accuracy, best practices and applied turbulence models. In this paper, we present a comprehensive study of motorcycle aerodynamics using CFD methods which, compared to the most common car aerodynamics analysis, has many specific features. The motorcycle, along with its rider, constitutes a shape with very complex aerodynamic properties. A detailed insight into the flow features is presented with detailed commentary. The front fairing, the front wheel and its suspension were identified as the main contributors to the aerodynamic drag of the motorcycle and its rider. The influence of rider position was also studied and identified as one of the most important elements when considering motorcycle aerodynamics. An extensive turbulence models study was performed to evaluate the accuracy of the most common Reynolds-averaged Navier–Stokes models and novel hybrid models, such as the Scale Adaptive Simulation and the Delayed Detached Eddy Simulation. Similar values of drag coefficients were obtained for different turbulence models with noticeable differences found for models. It was also observed that near-wall treatment affects the flow behaviour near the wheels and windshield but has no impact on the global aerodynamic parameters. In the summary, a discussion about the obtained results was set forth and a number of questions related to specifics of motorcycle CFD simulations were addressed.
The paper is focused on the mechanism of mixing process in a manifold which mimics the geometrical properties of vascular systems. The relationship governing the optimum ratio between the diameters of the parent and daughter branches in vascular systems was first discovered by Murray using the principle of minimum work. However, in contrast to biological vascular networks, which are composed of circular pipes, microfluidic manifolds are fabricated using a range of processes (photolithography, wet or dry etching, surface micromachining), which result in channels of rectangular or trapezoidal sections and constant depth throughout the device. The paper focuses on constant-depth rectangular channels often employed in lab-on-a-chip systems and provides comprehensive numerical studies of mixing in such geometry. It also presents simplified analytical estimation on how the coefficient of mixing depends on the number of generations and Reynolds number. The main goal of the paper is to describe the concept of a mixer which provides almost perfect mixing at the outlet regardless of the value of Re and for a minimal number of manifold's generations.
Although flows of fluids in curved channels belong to a classical problem of fluid dynamics, most publications are restricted to investigations of flows in tube coils, or in single bends. This paper presents experimental and numerical (CFD) results concerning Newtonian flows in a set of multiple S-type bends of various orientations. Investigations were conducted for a wide range of Re values (0–3500) and for a significant curvature ratio lying between 0.05 and 0.29, which corresponds to De value falling within the range 0.02–1200. A coiled tube was also examined and treated as the reference geometry. It was shown, that despite a completely different velocity pattern, the nonlinear dependence of normalized flow resistance of wavy tubes and coiled tube of the same curvature ratio overlap within a significant range of De. A novel, close phenomenological formula to estimate the nonlinear flow resistance of tortuous tube in a wide range of De was proposed and compared with those in the literature. The conditions were also determined in which the De might be the only dimensionless group that characterizes such flows.
Ensuring the transport of oxygenated blood to the brain is one of the priorities of the human body. In the literature, there are many models of cerebral circulation with different levels of complexity used to assess pathological conditions, support clinical decisions, and learn about the relationships governing cerebral circulation. This paper presents a zero-dimensional cerebral circulation model that considers hydrodynamic nonlinearities and autoregulation mechanisms. The model has been verified using a computational fluid dynamics (CFD) model of the Circle of Willis (CoW) and its supplying and outgoing branches. Despite the considerable simplicity, the presented model captured the dominant features of cerebral circulation and provides good agreement with the CFD model. The errors in relation to the CFD model did not exceed 2.6% and 9.9% for the symmetrical and highly asymmetrical CoW configurations, respectively. The practical application of the model was demonstrated for predicting the autoregulation pressure reserve for different diameters of natural anastomoses: Posterior and Anterior Communicating Arteries. The advantages and limitations of the model were discussed.