Jaehyo Kim

Prof. Jaehyo Kim

Handong Global University
orcid

Research Focus & Metrics

Academic Career Length

13Years (2014-Present)

(Calculated once Scilit publication data is synced: current year − year of first publication + 1)

Representative Publications

View All Publications
9 July 2018 in Biomedical Engineering Letters
Verified
Journal Article
Closed access
PDF file
HKHyeonseok Kim
Hyeonseok Kim
JLJongho Lee
Jongho Lee
Jaehyo KimJaehyo Kim
Jaehyo Kim

22 December 2016 in Advanced Robotics
Verified
Journal Article
Closed access
JKJihun Kim
Jihun Kim
JLJongho Lee
Jongho Lee
SKShinji Kakei
Shinji Kakei
Jaehyo KimJaehyo Kim
Jaehyo Kim
This paper investigates motor characteristics during circular tracking movements of human wrist. Ten subjects performed a visually guided target tracking task using two degrees-of-freedom wrist movements as a tracer. Based on trajectories of the tracer and the target, three control parameters in polar coordinates were considered: R error as an evaluation of the circular movement performance, theta error of the position-control precision, and omega error of the velocity-control precision. We then examined the influence of three different speeds (0.05, 0.1, and 0.2 Hz) and visibility of the target on the three parameters to observe changes in control strategy. The theta error particularly demonstrated that subjects were more dependent on position control for the lower tracking speed of 0.05 Hz with a visible target, where the highest percentage increase of 210.6% in theta errors from the target visible to the target invisible regions was reported. However, as the target speed increases, the subjects concentrated more on the velocity of the target as a main control parameter, and a minimum percentage decrease of 9.52% in the omega error appeared from target visible to target invisible regions for 0.2 Hz. The results suggest that velocity control is more dominant during target invisible or fast tracking task.

9 October 2020 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
JKJihun Kim
Jihun Kim
GLGeonhui Lee
Geonhui Lee
Hanjin JoHanjin Jo
Hanjin Jo
WPWookhyun Park
Wookhyun Park
YJYu Shin Jin
Yu Shin Jin
Jaehyo KimJaehyo Kim
Jaehyo Kim

10 October 2019 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
HKHyeonseok Kim
Hyeonseok Kim
JLJongho Lee
Jongho Lee
Jaehyo KimJaehyo Kim
Jaehyo Kim

19 June 2020 in Sensors
Verified
Journal Article
Open access
PDF file
WPWookhyun Park
Wookhyun Park
WCWoong Choi
Woong Choi
Hanjin JoHanjin Jo
Hanjin Jo
GLGeonhui Lee
Geonhui Lee
Jaehyo KimJaehyo Kim
Jaehyo Kim
Human movement is a controlled result of the sensory-motor system, and the motor control mechanism has been studied through diverse movements. The present study examined control characteristics of dominant and non-dominant hands by analyzing the transient responses of circular tracking movements in 3D virtual reality space. A visual target rotated in a circular trajectory at four different speeds, and 29 participants tracked the target with their hands. The position of each subject’s hand was measured, and the following three parameters were investigated: normalized initial peak velocity (IPV2), initial peak time (IPT2), and time delay (TD2). The IPV2 of both hands decreased as target speed increased. The results of IPT2 revealed that the dominant hand reached its peak velocity 0.0423 s earlier than the non-dominant hand, regardless of target speed. The TD2 of the hands diminished by 0.0218 s on average as target speed increased, but the dominant hand statistically revealed a 0.0417-s shorter TD2 than the non-dominant hand. Velocity-control performances from the IPV2 and IPT2 suggested that an identical internal model controls movement in both hands, whereas the dominant hand is likely more experienced than the non-dominant hand in reacting to neural commands, resulting in better reactivity in the movement task.

6 February 2015 in International Journal of Precision Engineering and Manufacturing
Verified
Journal Article
Closed access
PDF file
SLSungyoon Lee
Sungyoon Lee
HKHyeonseok Kim
Hyeonseok Kim
HJHeon Jeong
Heon Jeong
Jaehyo KimJaehyo Kim
Jaehyo Kim