Operation scheduling of apron support vehicles is an important factor affecting aircraft support capability. However, at present, the traditional support methods have the problems of low utilization rate of support vehicles and low support efficiency in multi-aircraft support. In this paper, a vehicle scheduling model is constructed, and a multi-layer coding genetic algorithm is designed to solve the vehicle scheduling problem. In this paper, the apron support vehicle operation scheduling problem is regarded as a Resource-Constrained Project Scheduling Problem (RCPSP), and the support vehicles and their support procedures are adjusted via the sequential sorting method to achieve the optimization goals of shortening the support time and improving the vehicle utilization rate. Based on a specific example, the job scheduling before and after the optimization of the number of support vehicles is simulated using a multi-layer coding genetic algorithm. The results show that compared with the traditional support scheme, the vehicle scheduling time optimized via the multi-layer coding genetic algorithm is obviously shortened; after the number of vehicles is optimized, the support time is further shortened and the average utilization rate of vehicles is improved. Finally, the optimized apron support vehicle number configuration and the best scheduling scheme are given.
Long landings can reduce runway utilization and increase the probability of runway incursions and excursions. Previous studies on long landings often lacked support from actual operational data and primarily relied on event-triggering logic established by airlines for parameter exceedance detection and retrospective analysis. In response, a comprehensive risk prediction framework for aircraft long landings, supported by Quick Access Recorder (QAR) data, was constructed. The framework includes a data analysis pipeline, a sequence prediction model, and performance evaluation metrics for accident warning efficiency. Specifically, approximately 3 million rows of real QAR data were collected, and reasonable landing intervals were extracted based on pilots’ correct landing sightlines, attention allocation, and actual visual scenarios at departure heights. Gradient Boosting Decision Trees (GBDT) were employed to develop a method for extracting landing interval feature data, based on monitored parameters and ranges of landing distance. Additionally, the GBDT-Informer long-sequence time series prediction model was developed to forecast landing distance, accompanied by the construction of effective metrics for evaluating prediction performance. The results indicate that the GBDT-Informer model effectively models the temporal dimensions of landing intervals, accurately predicting ground speed (GS), radio altitude (RALT), and landing distance sequences. Compared to other prediction models, the GBDT-Informer model consistently achieved the smallest RMSE, MAE, and MAPE values, demonstrating high prediction accuracy. This predictive framework allows for the analysis of the coupling relationships among multiple parameters in flight data and their interrelations with exceedance anomalies. The findings can be applied in actual flight landings to promptly assess whether landing distances exceed limits, providing quick references for flight crews during landing or go-around decisions, thereby enhancing operational safety margins during the landing phase.
In view of the fact that there is no suitable measurement method for tire driving resistance during the operation of a transporter on soil pavement, this paper proposes a simple measurement and estimation method for driving resistance on a soil runway based on the Bekker settlement model. In this paper, using the driving resistance equation based on the Bekker model, a simplified equation of driving resistance related to mass is proposed. Using the principle of kinematics, a simple test device for driving resistance was developed, and the test data of the test device were used to determine the parameters of the driving resistance estimation equation of the road surface. The driving resistance of the wheel running state was tested by the simulated aircraft load loading vehicle through the mechanical sensor, and the consistency between the theoretical value and the actual value of the driving resistance value under 8T, 10T, and 12T loads was verified. This research shows that the test method and estimation method have low cost and good accuracy and are suitable for wide promotion. The results of this paper provide a new idea and method for estimating the driving resistance of a wheel when a transporter runs on a soil road and also provide a reference for designing the length of a soil runway.
The large-displacement shear behavior of crushable granular interfaces is critical to pile foundations in reef engineering, but the coupled evolution of strength, deformation, and particle breakage at coral sand–steel interfaces remains poorly understood, especially regarding shear rate effects and the transition from coral-sand-dominated to quartz-sand-dominated behavior. Ring shear tests were conducted on dry coral sand–steel interfaces under constant normal load (CNL) conditions, varying normal stress, relative density, shear rate, and quartz-sand content. Post-shear particle-size distributions were used to quantify breakage via Hardin’s relative breakage index. Results show that peak and residual strengths increase with normal stress, with relative density effects becoming more evident at higher normal stress. Dilatancy is suppressed as normal stress increases. Peak strength depends non-monotonically on shear rate, peaking near 6°/min, while residual strength is much less rate-sensitive. Increasing quartz-sand content reduces strength and breakage and promotes dilation. Transition ranges at approximately 30% and 85–90% quartz-sand content indicate a shift from coral-sand-dominated to quartz-sand-dominated behavior. Persistent contraction at large displacements, attributed to particle breakage and fines infilling, may cause additional settlement. These findings clarify the coupled roles of breakage and composition in interface behavior.