Indium‐based transparent conducting electrodes (TCEs) are a major limiting factor in perovskite/silicon tandem cell scalability, while also limiting maximum cell efficiencies. In this work, we propose a novel TCE based on electrostatically doped graphene monolayers to circumvent these challenges. The electrode is enabled by a thin film dielectric that is charged and interfaced to a graphene film, optimally exploiting electrostatic doping. The field effect mechanism allows the modulation of charge carriers in monolayer graphene as a function of charge concentration in the dielectric thin film. Electrostatic charge was deposited on SiO2 membranes, and graphene transferred onto them exhibited a reduction in sheet resistance because of the induced charge carriers. We show a reduction in sheet resistance of graphene by 60% in just 3 min of dielectric charging, without impacting the transmission of light through the film stack. Hall effect measurements indicated that the mobility of the films was not significantly degraded. The deposition of negative electrostatic charge reversed this effect, allowing for precise tunability of charge concentration from n‐ to p‐type. We develop a model to determine the required sheet resistance of a graphene TCE with 97% transmittance in a perovskite/silicon tandem cell. As the technique here reported does not impact transmittance, a graphene TCE with a sheet resistance below 50 Ω/□ could enable efficiencies up to 44%, presenting a promising alternative to indium‐based TCEs.
Two novel chromium oxide arsenide materials have been synthesized, Sr2CrO2Cr2OAs2 (i.e., Sr2Cr3As2O3) and Sr2CrO3CrAs (i.e., Sr2Cr2AsO3), both of which contain chromium ions in two distinct layers. Sr2CrO2Cr2OAs2 was targeted following electron microscopy measurements on a related phase. It crystallizes in the space group P4/mmm and accommodates distorted CrO4As2 octahedra containing Cr2+ and distorted CrO2As4 octahedra containing Cr3+. In contrast, Sr2CrO3CrAs incorporates Cr3+ in CrO5 square-pyramidal coordination in [Sr2CrO3]+ layers and Cr2+ ions in CrAs4 tetrahedra in [CrAs]- layers and crystallizes in the space group P4/nmm. Powder neutron diffraction data reveal antiferromagnetic ordering in both compounds. In Sr2CrO3CrAs the Cr2+ moments in the [CrAs]- layers exhibit long-range ordering, while the Cr3+ moments in the [Sr2CrO3]+ layers only exhibit short-range ordering. However, in Sr2CrO2Cr2OAs2, both the Cr2+ moments in the CrO4As2 environments and the Cr3+ moments in the CrO2As4 polyhedra are long-range-ordered below 530(10) K. Above this temperature, only the Cr3+ moments are ordered with a Néel temperature slightly in excess of 600 K. A subtle structural change is evident in Sr2CrO2Cr2OAs2 below the magnetic ordering transitions.
Though patch clamping at room temperature is a widely disseminated standard procedure in the electrophysiological community, it does not represent the biological system in mammals at around 37 °C. In order to better mimic the natural environment in electrophysiological studies, we present a custom-built, temperature-controlled patch clamp platform for upright microscopes, which can easily be adapted to any upright patch clamp setup independently, whether commercially available or home built. Our setup can both cool and heat the platform having only small temperature variations of less than 0.5 °C. We demonstrate our setup with patch clamp measurements at 36 °C on Jurkat T lymphocytes and human induced pluripotent stem cell-derived neurons. Passive membrane parameters and characteristic electrophysiological properties, such as the gating properties of voltage-gated ion channels and the firing of action potentials, are compared to measurements at room temperature. We observe that many processes that are not explicitly considered as temperature dependent show changes with temperature. Thus, we believe in the need of a temperature control in patch clamp measurements if improved physiological conditions are required. Furthermore, we advise researchers to only compare electrophysiological results directly that have been measured at similar temperatures since small variations in cellular properties might be caused by temperature alterations.
Doping two-dimensional (2D) semiconductors without direct chemical or structural modification of the channel remains a central challenge for device integration. Here we demonstrate an electrostatic doping strategy on monolayer MoS2 based on embedding fixed charge in engineered dielectric stacks, enabling carrier modulation in the absence of volatile external bias. By comparing different dielectric architectures, we show that effective electrostatic doping is governed by the defect landscape of the capping dielectrics and their interface with the 2D channel. A self-consistent electrostatic model reveals that interface states control the partitioning of the dielectric embedded charge between carriers trapped in defects or free for conduction in the channel, posing limits to the effectiveness of electrostatic coupling. This work establishes electrostatic doping as a viable strategy for carrier modulation in 2D semiconductors and identifies dielectric defect engineering as central to its implementation.
Transparent conducting oxides (TCOs) are essential for the optoelectronics industry, but there is a critical gap in cost‐effective methods to rapidly deposit low‐sheet‐resistance, high‐transmittance films without damaging delicate materials, including emerging soft semiconductors like metal‐halide perovskites. In this work, atmospheric pressure chemical vapor deposition (AP‐CVD) is used to synthesize H:In 2 O 3 films with 7.20 ± 0.01 Ω □ −1 sheet resistance (0.50 ± 0.06 mΩ cm resistivity) and transmittance up to 89% in the near‐infrared (NIR), surpassing commercial sputter‐deposited indium tin oxide. The growth rate is 40 higher than atomic layer deposition (ALD), and the AP‐CVD films are fully processed under atmospheric conditions at only 140 °C. Comparison of secondary ion mass spectrometry and time‐of‐flight elastic recoil detection analysis with changes in carrier concentration indicates that H dopants are introduced from the water oxidant. There is an increase in mobility from 40 ± 10 cm 2 V −1 s −1 to 160 ± 30 cm 2 V −1 s −1 when changing from O 2 to H 2 O as the oxidant, which is attributed to hydrogen‐mediated passivation of defect‐related electronic states that would otherwise act as carrier scattering centers. This work establishes AP‐CVD as a promising method for manufacturing high figure‐of‐merit TCOs in a rapid, scalable, and cost‐effective manner, using mild growth conditions compatible with thermally‐sensitive materials.